Craftsman Control Cable

This part is a height adjustment cable that is used on lawnmowers. The height adjustment cable allows the lawnmower operator to adjust the height of the control bar to match his or her height.A new height adjustment cable will be needed if the original is no longer allowing the operator to adjust the height. If any portion of the height adjustment cable is cracked, broken, or damaged in any way, it will need to be replaced if the height of the control bar needs to be changed. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Never perform care and maintenance on outdoor power equipment that is powered on.This height adjustment cable is a genuine MTD part. It is sold individually. This particular height adjustment cable is compatible with lawnmowers that are manufactured by MTD.

Control cable that operates the chute lock mechanism on your snowblower. Connects chute lock to control lever. Replace if cable is frayed, broken, or stretched.

Replacement auger clutch control cable for gas snowblowers. Connects handle lever to auger engagement mechanism. Needed when cable is frayed, stretched, broken, or missing.

Drive control cable for snowblowers. Connects drive control handle to engine mechanism. Replace if cable is frayed, broken, kinked, or detached.

Drive control cable engages the gear case on self-propelled lawn mowers. Replace if cable is frayed, broken, or stretched causing loss of drive function.

Replacement clutch cable that connects the control lever to the drive clutch on your snow thrower. Needed when the original cable is frayed, broken, or worn.

Control cable for chipper shredders. Connects operator controls to clutch mechanism. Replace if cable is frayed, broken, or no longer engaging properly.

Steering control cable for gas snowblowers. Connects steering mechanism to handlebars. Replace if cable is frayed, broken, kinked, or disconnected.

Control cable for gas walk-behind mowers. Installs to operate speed control or drive engagement. Replace if cable is frayed, broken, or stretched.

This genuine OEM Part is a choke temperature control rod for lawnmowers. The choke temperature control is the metal piece that regulates the choke temperature allowing for it to function properly within a lawnmower. If the choke function is no longer working efficiently, it might be time to replace the choke temperature control. Luckily, replacing this part is a simple repair.Before beginning, make sure the engine is cool to avoid getting burned. Locate the old choke temperature control rod and remove the screws to the mounting assembly that hold the rod in place. Once removed, lift the old choke temperature control out and away from the mower and set it to the side. Replace with the new control rod and secure the mounting screws. Start up the mower to see if the choke function is working properly. If it does, the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This throttle assembly cable is manufactured by Craftsman, but also used by Poulan, to regulate the flow of fuel to certain small gasoline-powered engines. This assembly houses the throttle trigger that is used by almost a dozen different machines, including not only trimmers, but also pole saws and other small gasoline-powered tools. Apart from the cutting edges of the pole saws and trimmers, the parts of these devices that sees the most wear and tear, and is most likely to fail, are the throttle assemblies. Whether banged about because of proximity to the throttle trigger or simply because it's the only part protruding from the mid-body of the typical weed cutter, the throttle assembly housing and cable are susceptible to failure. Most often, failure of the cable is the result of one of the buds, attached at the ends to clasp securely, having broken off. In this case, the gasoline engine may start, but will not rev or only does so sporadically. Replacing the cable is a matter of removing the throttle housing and trigger as well as detaching the cable from the carburetor. When replacing the cable, be sure to use one like this, which is a genuine OEM replacement part, manufactured to replicate the specs of the original.

Replacement wheel adjustment control cable for edgers and gas line trimmers. Connects control handle to wheel height mechanism. Order if broken or frayed.

Control cable for walk-behind mowers. Connects handle controls to engine or drive system. Replace if cable is frayed, broken, or no longer engaging properly.