Crosley Heating Element

Restore steady cooking performance with this surface element coil. The 6-inch, 1250-watt burner replaces a worn or open coil so your range heats properly for everyday simmering, sautéing, and boiling.

• Generates heat on a 6-inch cooking zone for boiling, sautéing, and simmering
• Fixes a burner that won't heat or only heats intermittently
• Addresses uneven heating or unusually slow warm-up
• Helps when the coil shows visible breaks, blistering, or burned spots

• Disconnect power at the breaker and let the cooktop cool completely
• Remove the old coil and inspect the receptacle/terminal block; replace if burnt or loose
• Align prongs and press the new coil fully into the receptacle; ensure the support bracket seats in the drip pan notch
• After installation, test the burner with a pan to ensure even heating

This 6-inch radiant surface element is the heating source for a small burner beneath a glass-ceramic cooktop. Replacing a failed element restores reliable, controllable heat to that cooking zone. What it does:

• Heats the 6-inch cooking zone under the glass top when the control is turned on
• Cycles to help maintain the selected temperature during cooking
• Common symptoms of failure: small burner won't heat, heats unevenly or intermittently, or shows visible burn spots/damage

• 1 six-inch radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift the glass top or remove the cooktop to access the elements; support the glass to avoid stress or cracks
• Note wire positions and transfer connections to the new element one at a time
• Ensure the element sits flat in its mounting brackets before reassembly and testing

This oven bake element supplies the lower-oven heat for Bake cycles. Replacing a failed element restores proper preheating and consistent temperatures so your electric range or wall oven bakes reliably again. What it does:

• Provides radiant heat from the bottom of the oven during Bake
• Helps the oven reach and maintain the set temperature
• Failure symptoms can include: no heat in Bake, very slow preheating, uneven baking, or the element not glowing
• Visible damage such as breaks, blisters, or burned spots indicates replacement is needed

• One bake element

• Disconnect power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws, then gently pull the element forward and transfer the wires one at a time
• Reuse existing mounting hardware; ensure terminals are fully seated and not contacting the oven cavity
• Restore power and test Bake; the element should heat evenly

This 8-inch coil surface element restores reliable heating on the large burner of electric ranges and cooktops. Its 2350-watt design provides steady, even heat for boiling, frying, and everyday cooking.

• Converts electrical power into heat for the large cooktop position
• Common failure symptoms: no heat, uneven heating, only part of the coil glowing, visible breaks or blisters, or failed continuity
• Plug-in coil style for receptacle-type burner sockets
• If no heat persists after replacement, also inspect the element receptacle and the burner switch

• Disconnect power to the range/cooktop and allow the element to cool completely
• Lift the old element and pull straight out from the receptacle
• Align the new element's terminals with the receptacle, push in firmly until fully seated, and set it into the support/drip bowl
• Restore power and test the burner

2100W. Size: 8 inch. Location: Right front.

This surface heating element is the electric heat source for a cooktop burner on an electric range. Replacing a worn or open element restores steady, responsive burner heat for everyday cooking. What it does

• Converts electrical energy to heat for the selected surface burner
• Works with the surface control to cycle heat and maintain set temperature
• Common symptoms: burner won't heat, heats weakly or intermittently, or shows visible hot spots/burn marks on the element

• 1 surface heating element

• Disconnect power at the breaker before servicing and let the cooktop cool completely
• Access the element by lifting/removing the cooktop or burner pan per your model's service procedure
• Photograph and label wire locations; move one connection at a time to the new element
• Transfer any mounting brackets or supports from the original element; avoid bending or stressing the element during install

Built for electric dryers that require a 240V heater, this complete heater assembly restores proper heat output. Replace a burned-out element to resolve no-heat or weak-heat complaints and return your dryer to consistent, efficient drying.

• Generates the hot air needed to dry laundry during the cycle
• Typical failure symptoms: drum turns but no heat, longer dry times, or intermittent heating
• Can be checked with a continuity test; a broken or grounded coil indicates replacement is needed
• Factory-style 240V configuration for proper operation on compatible models

• Disconnect power at the breaker before servicing
• Access the heater per your model's service procedure and document wire locations
• Move wires to matching terminals; transfer any attached brackets/sensors from the old assembly if your model uses them
• Clear lint and verify airflow before a test run to confirm proper heating and cycling

This 240-volt heater assembly restores the appliance's ability to generate and maintain heat during operation, helping cycles reach designed temperatures for proper performance and results. What it does:

• Converts electrical energy into heat for the appliance's heating circuit
• Helps the unit reach and hold target temperatures during heat-required portions of the cycle
• Replaces a damaged, shorted, or open heating element
• Symptoms can include no heat when expected, longer-than-normal cycles, tripped breakers, or heater-related error codes

• 1 heater assembly

• Disconnect power at the breaker before servicing; 240V circuits can be hazardous
• Document wire locations and move connectors one at a time to the new assembly
• Avoid bending or striking the element; ensure secure mounting and proper clearances
• After installation, check related safety devices (high-limit, thermostats, fuses) and verify the circuit has correct voltage and continuity

10-inch heating element that restores proper heat production in affected appliances. Replaces a worn or failed element to help resolve issues like no heat or unusually long cycle times. What it does:

• Generates heat so your appliance can reach normal operating temperatures.
• Common symptoms it addresses: little or no heat, longer-than-normal cycles, or intermittent heating.
• Replaces a single failed element to return consistent heating performance.

What's included: One heating element. Install notes:

• Disconnect the appliance from power before attempting any repair.
• Allow the element to cool and handle carefully to avoid bending or damaging the coil.
• Ensure the terminal connections are secure and free of corrosion; tighten or replace fasteners as needed.

NOTE: IF THERMISTOR HAS TERMINALS WIRE HARNESS HAS TO BE CHANGED PART# 137288900 PER FRIGIDAIRE

This 8-inch surface burner element delivers heat on an electric cooktop or range. Replacing a worn or open element restores even heating on the burner zone and reliable response to temperature settings.

• Heats the 8-inch cooking zone when the surface control is turned on
• Helps maintain consistent pan temperature for boiling, simmering, and frying
• Common symptoms: burner won't heat, heats unevenly or intermittently, visible blistering/breaks in the coil, or scorch marks at the terminals
• Replacing a damaged element can prevent further damage to the receptacle/terminal block

• Disconnect power at the breaker and allow the unit to cool completely
• Handle the element by the bracket; avoid bending the coil
• For plug-in setups, pull the old element straight out and firmly seat the new one; for wired connections, move wires one at a time to the matching terminals and secure properly
• Inspect the receptacle/terminal block and wiring; replace if burnt or loose before restoring power

This 8-inch surface element kit restores reliable heat on your electric range or cooktop. Replace a failed burner so pots heat evenly and settings respond as expected across your 8-inch cooking zone.

• Heats the 8-inch surface burner for everyday boiling, simmering, and frying
• Replaces a burned-out or damaged element to restore consistent performance
• Helps eliminate weak, uneven, or intermittent heating
• Common symptoms: surface burner won't heat, heats inconsistently, or shows obvious damage

• Disconnect power at the breaker or unplug the appliance before servicing; allow all components to cool completely
• Note wire/terminal positions and transfer any mounting parts from the old element if required
• Ensure terminals are fully seated and the element is properly supported/seated before use
• After installation, test on low and high settings to confirm proper operation

This element repair kit restores a safe, solid electrical connection to an electric range/cooktop surface burner, helping the element heat consistently and reducing arcing after the original connector has overheated or loosened.

• Repairs a damaged or heat-weakened surface element connection
• Helps resolve a burner that won't heat or heats intermittently
• Addresses visible scorching, melting, or arcing at the element plug-in
• Supports a snug, reliable fit for the element prongs

• Disconnect power at the breaker or unplug before servicing; allow the cooking surface to cool completely
• Match connector orientation and move one wire at a time to avoid miswiring
• Inspect wire insulation and element terminals; replace any parts with burnt, pitted, or loose contacts
• Ensure the element seats firmly after repair and verify proper operation before regular use

Size: 8 inch. 2200 watt. Radiant.

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

This 6-inch surface coil element restores reliable heat to one burner on your electric range. Replace a burned-out or damaged coil to bring back consistent, even heating for everyday cooking.

• Provides cooking heat for a 6-inch burner position on electric ranges/cooktops
• Helps resolve a burner that won't heat or heats intermittently
• Addresses uneven heating or visible hot spots on the coil
• Replaces elements with visible breaks, blistering, or burned terminals

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• For plug-in coil models: lift the element, pull straight out of the receptacle, and remove from the support/drip pan
• Align the new element's terminals with the receptacle, push firmly until fully seated, and set into the support
• Inspect the receptacle and wiring for heat damage and replace any compromised components before use

This is a replacement broil element for the oven's upper heating function. It restores high-heat broiling and top-surface browning so you can sear, brown, and finish foods as intended. What it does:

• Produces the direct, high heat required for broiling and browning
• Replaces a burned-out, visibly damaged, or non-heating upper element
• Restores even top-heat for recipes that require searing or finishing
• Helps eliminate weak or no heat from the oven's broil function

• One broil element

• Disconnect power to the appliance before starting any repair
• Allow the oven to cool completely and use basic hand tools to remove mounting screws and the old element
• Handle the new element carefully to avoid bending or damaging terminals