Crosley Parts

• Spins slowly
• Burning smell
• Pumps but will not spin
• Will not agitate

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

Ordered part from your website. Fit perfectly Read more

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

I think I have a lemon of a dryer. I keep having to pay someone to replace my heating element about every year. So I already had the heating element, but I thought I would replace the thermostat and the limiter also. Yes, I am a 46 year old mom, and I replaced all three items. Thank goodness to youtube! Ha! I have ordered from you before and you always send promptly. Thanks! Read more

Replaced the Gearcase assembly which is a sealed unit that is not serviceable. Also replaced the clutch and belt because they were covered in gearcase oil. Read more

Replace them. Out of two shelf guards 1 was broken Read more

• Ice maker dispenses too much ice

Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more

Pulled the washer apart (using your videos as a refresher) and found that the plastic coupling between the motor and the transmission had failed. Searched for parts vendors and found your site. Ordered the coupling on-line and went back down to clean up the machine. In the cleaning process I found a damaged thrust washer for the upper agitator and broken drive dogs for that same agitator. I went to the website to see if I could augment my initial order. I did not want to pay shipping costs... Read more

Replaced ignitor. Very simple project. Read more

Purchased the gasket, but upset with myself I forgot the high temp adhesive.....a 13$ part and now 7$ for shipping. Think not for my mistake Read more

It was a fast fix. its a Maytag Centennial Top load washer. it took me about 20mins to remove the pump and instal the new one.Most of the time was spent moving the washer. Read more

• Won't start
• Noisy

Replaced the pump motor. Works great again. I saw the picture of the part on the website so I knew I was getting the right part and watched the video to see if there were any shortcuts. Easy job. Read more

I ordered the plastic frames from Applianceparts.com. When they arrived I placed the unbroken glass within the frames. Very simple! Read more

First, I paid for two-day shipping, but the part arrived the day after I ordered. Awesome service!! For reference, I am a 28-year-old female with little repair experience (though I'd consider myself pretty handy in general and able to figure out most things in life - not a damsel in distress.) This was a relatively easy fix once you figure out how to take down the motor housing, unsure of correct terminology, hard to find a diagram out there that provides a name for all of the parts, where the... Read more