Crosley Parts

Snapped off the old part and snapped on the new one. All of two minutes. Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

It was the day of my birthday June 6th when my wife came to me to tell me that the dryer was not working. Immediately I started to look for a new dryer from Best Buy and the rest. Then I said It would be better if I waited for 4th of July at which time I could find a better deal. This is when I decided to take it apart to see what was wrong. Initially, I thought of the belt that could be broken and I rotated the drum by hand and I heard a noise of the belt at times falling on the drum. I was... Read more

I watched the AppliancePartsPros.com video, which made the replacement of an ice maker look pretty easy. The only problem was that my existing wiring harness was affixed to the inside of my refrigerator, whereas in the video, the existing cord was shown as readily disconnectable, so I was unsure how to proceed. Then I saw a comment by another user, expressing the same issue. The AppliancePartsPros representative advised the consumer simply to retain and use the existing, affixed wiring... Read more

• Lid or door won't close
• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

Replaced it with a new one Read more

If you can't pull out the displacement pins on the crisper cover support clips that allow the wall to carry the weight of the cover, slides and drawer, you may need to push those pins in (they fall down the wall) to remove the clip. During the replacement of both front clips, I had one I could remove and one I had attempted to drill a tiny hole in to be able to pull the pin. Ultimately it did not work and needed to be simply pushed in. Do not worry, there is nothing below which the plastic... Read more

I ordered a replacement Crisper Pan Cover and two Crisper Pans. Your price was the best and parts were delivered in two business days. The parts were generously wrapped in heavy duty bubble wrap. I removed the glass from the original (badly cracked) Crisper Pan frame and popped it into the new one. That took barely a minute...and then the new drawers slid right in. Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Fills and drains at the same time

I watched the how-to video on your website to learn how to get at the valve to replace it. Before watching the video, I did not know how to take the washer cabinet apart to replace the valve. I searched on your website for my washer model, but the exact model number was not listed. I chose a very similar model number and looked up the info for that machine's replacement valve . It looked like it would work in my washing machine so I decided to take a chance and order the valve. I placed my... Read more

Replaced the water solenoid. Read more

I ordered a replacement part. Emptied the top shelf then took the shelf out. Flipped the shelf over and removed the screw holding the broken piece. Put the new piece in its place replaced screw. Put the shelf back in and then put the mean pan back on the hangers. Read more

• Door sweating
• Door won't open or close
• Clicking sound
• Fridge too warm

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

Took broken bin out and replaced with new one. No tools were required ( for the next section since it won't allow me to only select other). Read more

Installed new sprayer arm. It was super easy. Read more

• Fridge too cold
• Fridge runs too long
• Won't start
• Freezer section too warm

The 20 year old unit still serves us well, looks good and has been kept in good repair. The condenser fan had stopped so I removed, cleaned and oiled that motor. The decision was made to make an upgrade to the evaporator motor and control units so that the appliance could reasonably be expected to have extended service life. The Ice maker module had been replaced 7 years ago. I ordered the parts and have made the upgrade for temperature controller and the defrost control. If you are in a... Read more