Need Help?
Call
One piece. Works on most Maytag washers. Color: white. It measures about 5 inches in diameter, and 5-1/2 inches high.
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
Usually ships within 4 - 14 days
Plastic door cover
Removed from dryer with screwdriver and opened door to access outer glass panel. Replaced with new one and reassambled. Read more
This replacement door glass forms the clear window in the door of select front-load units, restoring safe visibility and proper door fit. Replace a cracked, chipped, or shattered pane to prevent leaks and ensure the door seals and latches correctly. What it does
Replacement drain hose for washers. Routes wastewater from the drain pump to your household drain. Replace if cracked, leaking, clogged, or worn.
It was a nice match thnx alot Read more
Washer bearing supports drum rotation during spin cycles. Replace if washer makes loud grinding or squealing noises. Verify fit with your model number.
Replace bearing. This was a veryy involved job since I had to disassemble the entire washing machine. Since previously I purchased a seal kit, it came in handy for this repair.Machine is much quieter now. Read more
Replacement power cord for your washer. Installs between appliance and wall outlet. Replace if original cord is damaged, frayed, or cracked.
Supports the washer transmission shaft to reduce axial wear and noise. Replace when you hear grinding sounds or experience rough operation. Confirm fit with your model number.
Washer won't spin or stops mid-cycle? This tub displacement switch senses water level and balance to restore proper spin operation. DIY-friendly fix.
I had the problem couple years ago I bypassed unbalance switch it worked fine for a couple years and had the same problem again so ruled out unbalanced switch. Door lock light on and checked made sure wax motor pushed out all the way too the second switch for spin check OK, so took a chance on displacement switch x2. My family loves to over load it and also replaced by passed unbalance switch and boom every thing went back to normal. Its also good to clean every thing when apart. Read more
This is a left-side lid hinge for a top-load washing machine. It connects the lid to the washer cabinet and allows it to open and close smoothly. Replace this hinge if the lid feels loose, does not stay open, sits unevenly, or if the hinge is cracked or broken.
I removed the old broken hinge and replaced it with the proper new part. Two screws out, place hinge and screw it in place. Easy and quick. Read more
Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.
This power cord supplies electrical power to the appliance and replaces a damaged or worn cord to restore safe, consistent power delivery. The "as wrapped" packaging means the cord ships neatly coiled for protection in transit. What it does:
This is a rubber hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. Over time this hose can crack, clog, or develop leaks. Replace it if you notice detergent not reaching the tub, water leaking near the dispenser area, or visible deterioration of the hose.
Removed the material and replaced hose. Read more
Assorted fasteners, clips, and hardware for washer repairs. Replace missing or damaged clips during panel removal or component service. Verify fit with your model.
Replacement tub cover for washers. Covers the top of the outer tub assembly. Order a new cover if yours is cracked, broken, or damaged.
If your washer won't advance cycles or overfills, the pressure switch likely failed. This DIY repair restores water level sensing in 15-30 minutes.
First I unplugged the power cord for the washer. I removed the back plate of the control panel. Then removed the knob and unscrewed the screw holding the broken pressure switch. I then swapped the three electrical cables one at a time and placed on the new pressure switch. Then I put the screw in to hold the switch in place. I replaced the knob, plugged in the washer and turned it on. The appliance immediately worked. Read more
Spesc: #12 pozi - drive
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.