Crosley Washer Parts

Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.

This siphon break kit prevents water from siphoning back out of the washing machine tub through the drain hose during the fill cycle. It acts as an air gap device installed on the drain line to ensure proper water levels are maintained. Replace this kit if your washer is not filling properly, takes too long to fill, or you notice water draining out as fast as it fills.

Secures shafts and pulleys in your washer to prevent axial movement. Replace when worn or damaged to restore proper alignment. Confirm fit with model.

Exterior upper cover panel for washers. Restores a finished look and protects internal components. Replace if cracked, dented, or damaged from impact.

This small tube of Molykote lubricant helps reduce friction on moving appliance parts for smoother operation and quieter performance. Use it where the manufacturer specifies a silicone/grease lubricant to restore proper movement and limit wear. What it does:

• Lubricates bearings, rollers, hinges, and other sliding contacts to reduce noise and friction
• Helps parts move more smoothly and can prevent rough operation or squeaks
• Can protect metal-on-metal contact from premature wear when applied as directed
• For use only in areas the manufacturer specifies for Molykote-type lubricants

• Apply sparingly to the specified contact points; excess can attract dirt or drip onto other parts
• Wear gloves and avoid skin/eye contact; wash hands after use
• Keep out of reach of children and store in a cool, dry place

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

Connects the drain hose to the washer drain outlet. Replace this coupling kit if cracked, broken, or leaking to restore a secure connection.

A stabilizer bracket that secures and supports internal components to reduce movement and rattle during operation. Helps restore stable alignment so the appliance runs quieter and more reliably. What it does:

• Provides structural support to help keep assemblies aligned and reduce excessive movement
• Dampens vibration and minimizes knocking or rattling noises tied to loose components
• Restores proper fit where a worn or broken bracket allowed shifting or misalignment
• Works as a repair for symptoms like intermittent noise, excess vibration, or parts that sag or shift

• Disconnect power (and water if appliance-specific) before beginning any repair
• Basic hand tools are usually required; refer to your model's service manual for exact steps
• Inspect surrounding parts for wear while replacing the bracket

This is a flat steel washer with approximate dimensions of 28.65mm inner diameter, 39.6mm outer diameter, and 0.965mm thickness. It serves as a spacer or fastener component in various appliances, helping to distribute load and prevent loosening of bolted connections. Replace this washer if it is cracked, deformed, or corroded, which can cause rattling, loose fittings, or improper alignment of parts.

Secures U-shaped drain hoses or heating elements in washers. Replace if cracked, broken, or missing to prevent hose movement and potential leaks.

Shipping bolt for washers. Secures the drum during transport to prevent damage. Replace if missing, stripped, or lost before installation.

This kit includes a siphon break device that installs on the washer's drain hose connection to prevent water from siphoning back into the machine. It acts as an anti-siphon valve, ensuring proper drainage and preventing dirty water from flowing back into the wash tub. Replace this part if your washer is not draining properly, fills and drains at the same time, or if the existing siphon break is cracked or leaking.

Shipping bolt kit secures the washer drum during transport. Replace missing or lost bolts when moving your washer to prevent damage to the suspension system.

Silicone lubricant grease for washer bearings and seals. Replace during bearing or tub seal repairs to ensure smooth operation and prevent wear. 2 oz.

This is a small rubber o-ring that seals the drain pump filter cap on a front-load washer. It creates a watertight seal between the filter cap and the pump housing, preventing leaks during the wash and drain cycles. Replace this o-ring if you notice water dripping or pooling near the drain pump filter area at the front bottom of the washer.

Broken or cracked dispenser drawer causing detergent leaks? Replace your washer's detergent drawer. Easy 90-second install, no tools needed.