Dishrack

This dishrack replaces a damaged or rusted rack in your dishwasher. Restoring a true-to-spec rack keeps plates, bowls, and cookware secure and properly spaced so the machine can clean effectively and the rack moves smoothly on its tracks. What it does:

• Organizes and supports dishes and cookware during wash and dry cycles
• Maintains proper spacing for spray coverage and drainage
• Interfaces with the rail system to slide in and out when paired with the correct rollers/stops for your model
• Common symptoms: rusted or broken tines, deteriorated rack coating, misshapen frame, rack falling off tracks or not sliding properly

• 1 dishrack

• Disconnect power to the dishwasher before servicing
• Open the door; pull the existing rack out. For upper racks, release/remove rack stops or end caps; for lower racks, lift straight out
• Transfer any reusable components (rollers, clips, fold-down tines, silverware basket) from the old rack
• Slide the new rack onto the rails and reinstall stops; verify smooth travel before running a cycle

Color: light gray. Measures about a 1/2 inch high by 4 inches deep.

This upper rack adjuster sets and secures the dishwasher's top rack height so dishes clear the spray arms and load properly. When the adjuster wears or breaks, the rack can become uneven or stuck, leading to poor cleaning and loading issues.

• Provides the mechanism to raise/lower and lock the upper dishrack height
• Keeps the top rack level and secured to the rail during operation
• Common symptoms of failure: rack drops on one side, won't adjust, feels loose, or comes off the track
• Contribute to poor wash results when the rack can't be positioned correctly

• Disconnect power and water supply before servicing
• Remove upper rack end caps/stops and slide the rack out to access the adjuster
• Release or unfasten the old adjuster, transfer any reusable clips/wheels if applicable, and install the new adjuster
• Set both sides of the rack to the same height; reinstall rack and confirm smooth travel and secure locking

Color: gray. Each clip measures about an inch and each pack includes 2 clips.

Used on the upper rack track

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

Color: White. This basket measures about 9 inches wide by 7 inches high by 6 inches deep. The cover and handle are not included. The cover is no longer available. For the handle order W11033847.

Color: gray. Measures about 1 inch high by 1-1/2 inches deep.

This small retainer clip secures a mating part in the correct position inside your appliance, helping prevent movement, premature wear, and noise. Replace a cracked, bent, or missing clip to restore a tight, reliable hold.

• Provides a positive hold to keep the component properly seated
• Maintains alignment to reduce vibration and rattling during operation
• Helps prevent parts from backing out or disconnecting over time
• Common signs of failure: loose or misaligned component, rattling, clip that falls off, or visible damage

• Disconnect power; if working near any water connections, also shut off the water supply
• Note the clip's original orientation and position before removal
• Use needle-nose pliers or a small flat-blade screwdriver to release/install; avoid deforming mating tabs
• Ensure full engagement and that the secured part is firmly held before reassembly and testing

The Tine Row Holder is an OEM part for LG dishwashers. It is a molded plastic bracket located inside the dishwasher that firmly holds the horizontal tine rows of the upper spray arm assembly in place. Subject to vibrations during the wash cycle, the tine row holder must securely grip this assembly.

Symptoms of a bad tine row holder include:

• Loosened or detached upper spray arm that causes insufficient washing 
• Rattling noises from loose components inside the tub 
• Potential leaks if the plastic material cracks fully over time

Causes of failure can include cracking of the holder plastic from solvent exposure and mineral buildup over thousands of wash cycles. Replace with this OEM LG part to ensure balanced water distribution to all areas of dishes. It is also compatible with Sears/Kenmore dishwasher models.

Color: blue. It measures about 3 inches wide by 1 inch high.

This dishrack organizes and supports dishes inside the dishwasher during wash cycles. Replacing a damaged rack restores smooth loading, keeps items upright, and helps prevent rust stains or snags from broken tines or flaking rack coating.

• Holds and organizes plates, bowls, and cookware during wash and rinse cycles
• Keeps items spaced and upright to promote spray coverage and drainage
• Slides in and out on the rails when the rack is straight and intact
• Common failure signs: rusting/chipping coating, broken or bent tines, cracked or warped wire frame
• Needed if dishes won't stay put or the rack binds when moving on the tracks

• Disconnect power at the breaker and turn off water before servicing interior parts
• Open the door, extend the rack, and remove rail end caps to release the rack
• Transfer any clip-on components from the old rack to the new rack as needed
• Seat the rack on the rails, reinstall end caps, and check for smooth operation

This replacement rack restores sturdy, organized loading inside your dishwasher. It helps keep dishes, glassware, and cookware securely positioned so they wash effectively without tipping, shifting, or being scratched by damaged or rusty tines. What it does:

• Holds and organizes items during wash cycles for stable, consistent placement
• Maintains proper spacing for spray coverage and drainage
• Direct replacement for racks that are cracked, bent, rusted, or missing tines
• Common signs: visible rust or flaking, broken welds, unstable sections, items tipping or not staying put

• 1 rack

• Open the door, fully extend the rack, and remove rail end caps or stops as your model requires
• Slide the old rack out; transfer any reusable components (such as rollers, clips, or accessory shelves) to the new rack
• Slide the new rack onto the rails and reinstall the end caps/stops; verify smooth movement
• Wear cut-resistant gloves; disconnect power if working near internal components or rails

The Silverware Basket is an OEM component specifically designed for Whirlpool dishwashers. Located at the bottom outer edge of the tub, the silverware basket provides designated silverware basket dishwasher spacing to properly clean utensils away from other dishes. 

Composed of crisscrossing finger prongs attached to a reinforced circular base, the basket holds forks, knives, and spoons upright safely in place during wash cycles. Its lightweight plastic construction flexes under pressure without breaking or cracking.

Symptoms of a bad silverware basket include:

• Loose or falling utensils obstructing other spray jets   
• Dull or improperly cleaned silverware after cycles
• Visible cracks, chunks missing, or sharp prongs

Replace with this OEM Whirlpool basket to restore form-fitting function. This part fits Whirlpool, KitchenAid, Jenn-Air and select Maytag and Amana dishwashers.

The Rack Stop is an OEM part for Frigidaire dishwashers. It serves an important purpose by preventing loaded dishes from shifting forward during wash cycles.

Causes of a bad rack stop can include wear and tear from regularly loading and unloading dishes, as well as minor impacts that cause cracks or breaks. Over time, the mounting screws may also loosen.

Symptoms of a bad rack stop include:

• Dishes shifting forward during wash cycles
• Gaps appearing around the dish rack where dishes are not fully secured
• Noise from dishes banging together or rattling around more than usual
• Potential damage to more delicate dishware

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken