Dryer Burner & Related Parts

This genuine OEM replacement part is a burner and gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential function. If the dryer is no longer drying clothes effectively or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is a relatively simple job.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the burner and gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old burner assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

This LP conversion kit contains the calibrated components needed to convert compatible natural gas appliances to operate on liquid propane, helping ensure proper fuel flow and flame performance when switching gas sources.

• Provides propane-rated orifices and components to adjust gas flow from natural gas to LP
• Helps correct issues like yellow, lazy, or oversized flames after a fuel change
• Supports safe, efficient burner ignition and heating on LP
• Used when local fuel supply is propane instead of natural gas

• For safety, shut off gas and electrical power before beginning; allow the appliance to cool
• Conversion must follow the appliance's service manual and LP instructions
• Adjust regulator setting and burner/orifice sizing per included and model-specific guidance
• Leak-test all gas connections with an approved method before restoring service

The Dryer Gas Valve is an essential component for your Samsung dryer, ensuring proper gas regulation and efficient drying performance. This genuine OEM part guarantees a perfect fit and reliable operation, matching the exact specifications of your appliance. Designed for durability, the Dryer Gas Valve maintains consistent gas flow, preventing interruptions during your drying cycles and enhancing overall dryer efficiency. Installing this gas valve helps restore your dryer's functionality, especially if the original component is faulty or worn out. Compatible with a wide range of Samsung dryer models, this part provides peace of mind with its high quality and dependable performance. Choosing this genuine OEM Dryer Gas Valve ensures safe operation and extends the lifespan of your Samsung dryer, allowing you to manage your laundry needs effectively and without hassle.

The LP Gas Conversion Kit is an OEM part for Whirlpool appliances. This kit allows for the conversion of natural gas appliances to use liquid propane (LP) gas. It includes all necessary components, such as orifices and instructions, to ensure a safe and efficient conversion.

Over time or due to specific needs, you might need to convert your appliance from natural gas to LP gas. Causes for needing this conversion include moving to an area where only LP gas is available or preferring LP gas due to its efficiency and environmental benefits.

Symptoms indicating the need for a gas conversion kit include:

• Moving to a location that only supplies LP gas
• Changing energy preferences for better efficiency
• Appliances set up for natural gas needing adaptation to LP gas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement gas valve controls gas flow to the burner in a gas dryer, enabling safe ignition and consistent heat. When it fails, the burner may not light and loads can stay damp; replacing it restores proper drying performance.

• Opens and closes gas flow to the burner when heat is called for
• Shuts off gas when the cycle ends or heating is not active
• Common symptoms: dryer runs but has no heat or the burner never ignites
• May present as the ignitor glowing or clicking repeatedly without flame, or intermittent heat

• Disconnect power and shut off the gas supply before servicing
• Work in a ventilated area and allow the dryer and burner to cool
• Use only gas-rated thread sealant on threaded connections
• After installation, turn on gas and check all joints for leaks with a soap-and-water solution

The Gas Valve Assembly is an OEM replacement part for LG gas dryers. It precisely controls the flow of gas to the burner unit during drying cycles. 

Symptoms of a faulty gas valve include: 

• Inadequate or inconsistent heating 
• Burner failure to ignite properly
• Error codes related to gas or pilot light issues

Causes may involve wear and tear of valve seals over extended use, blockages limiting gas flow, or damage like dents that compromise valve integrity.

This authentic LG assembly is compatible with select Kenmore brand models. 

This gas valve includes the coils. For the coils alone use part number 279834

This gas surface burner head distributes fuel through its ports to create an even, reliable flame on your cooktop. Replace a clogged, damaged, or warped head to restore consistent ignition and proper heat on the affected burner.

• Channels gas through precision ports to produce a steady, even flame
• Interfaces with the surface igniter/electrode for quick, reliable ignition
• Replaces worn or clogged heads that cause weak, uneven, or yellow flames
• Helps resolve delayed ignition or a burner that won't light

• Disconnect electrical power and shut off gas supply before servicing
• Remove grate and burner cap, lift off the old head, and clean the mating surface
• Align the new head with the igniter and locating features; seat it fully before replacing the cap
• Restore gas and power; test ignition and verify proper flame pattern

This valve and pipe assembly regulates and routes fuel through the dryer's system so the burner can ignite and maintain heat. Replacing a failing assembly restores reliable heating performance and consistent drying results. What it does

• Opens and closes to control fuel flow to the burner when heat is called for
• Directs fuel from the inlet to the burner orifice through a rigid manifold/pipe
• Helps maintain safe shutoff when the dryer is idle
• Common symptoms of a failing assembly: no heat, intermittent heat, or burner failing to ignite

• One valve-and-pipe assembly

• Disconnect power and shut off the gas supply before servicing
• Use only gas-rated fittings/sealant as specified by the manufacturer; do not overtighten connections
• After installation, check all joints for leaks with a soap-and-water solution
• Restore power and gas, then verify proper burner ignition and stable heating

This burner assembly is the gas/air mixing and flame head for gas dryers. Replacing a warped or corroded burner restores reliable ignition and steady heat so loads dry evenly and cycle times return to normal.

• Mixes incoming gas with air and directs it to the igniter for proper light-off
• Produces a stable flame to heat the dryer's airflow
• Replaces burners that are bent, rusted, or clogged and affecting ignition
• Typical symptoms: no heat, burner won't light, intermittent heat, or long dry times

• Disconnect power, shut off gas, and allow the dryer to cool before servicing.
• Access the burner compartment; note component positions and wiring for reassembly.
• Protect the igniter and sensor mounted near the burner from impact.
• After reassembly, restore gas and check all connections with a leak-detection solution; verify proper ignition and flame.

For propane order 383EEL3002A.

Liquid propane to natural gas

This gas valve regulates and safely delivers fuel to your dryer's burner. When operating correctly, it opens for ignition and closes when heat is satisfied, providing consistent, reliable heating for effective drying.

• Opens to allow gas into the burner when the ignition system calls for heat
• Closes to stop gas flow during cycling or if ignition fails
• Possible symptoms: dryer runs but no heat; igniter glows yet no flame; intermittent heat or long dry times
• Helps restore proper burner ignition and stable flame

• Disconnect power and shut off the gas supply before servicing
• Work in a well-ventilated area; check all connections for leaks with a non-corrosive leak-detection solution after installation
• Transfer any brackets, fittings, or orifices from the original valve as required; secure connections
• Confirm gas type (natural/LP) and regulator/orifice settings per the service manual before restoring service

This Kit includes the Regulator Lock Limiter, the Main Orifice Spud and the instruction sheet.

This genuine OEM replacement part is a gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential functions. If the dryer is no longer drying clothes effectively, or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is an easy fix.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old valve assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

This burner assembly restores proper gas flame and heat in your dryer. It directs and mixes gas and air for clean ignition at the igniter, helping clothes dry efficiently and consistently.

• Provides the flame path and mixing chamber for gas ignition
• Helps resolve symptoms like no heat, intermittent heat, or very long dry times
• Can address issues where the burner won't ignite or the flame will not stay lit
• Designed to fit the factory burner mount and align with the igniter and flame sensor

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Access is typically from the front lower panel or burner compartment
• Transfer any reusable hardware from the original assembly if required
• After reassembly, restore gas and check all connections for leaks using a soapy water solution