Dryer Gasket & Seal

Seals the dryer door to keep heat and moisture inside the drum. Replace when worn to restore airflow, improve drying, and stop lint escape.

Replace your worn dryer door seal to restore a tight closure, contain heat and moisture, and eliminate rattling or squeaking. Easy snap-in install.

This replacement seal restores a tight barrier at its mounting point in your appliance. It helps prevent leaks and maintains performance by ensuring a proper fit between connected components where fluids or air must be contained. Location varies by model.

• Creates a reliable seal between mating parts to contain water or air
• Helps stop drips, seepage, and unwanted airflow that can affect performance
• Replace if cracked, flattened, swollen, or leaking
• Common symptoms: moisture under/around unit, residue, or diminished efficiency
• Direct-fit replacement to match the original part's size and profile

• Disconnect power and, if applicable, shut off water supply before servicing
• Note the original seal's orientation; clean and dry all sealing surfaces
• Lightly moisten or use only manufacturer-approved lubricant; avoid petroleum products unless directed
• Seat evenly without twisting; after reassembly, run a test cycle and check for leaks

Right hand side. Used most Admiral, Crosley, Norge, and Magic Chef dryers. Includes glide and felt pad.

This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:

• Seals the gap between the door and oven frame to minimize heat loss
• Helps the oven preheat faster and hold set temperatures more consistently
• Replace if the gasket is torn, brittle, flattened, or frayed
• Common signs include heat escaping around the door edge and longer cook times

• 1 door seal

• Disconnect power and allow the oven to cool completely before beginning
• Open the door and carefully remove the old seal, noting its routing and attachment points
• Clean the mating surface to remove debris for a proper seal
• Install the new seal evenly without stretching; ensure all ends and anchors are fully seated

Seals the dryer door perimeter to contain heat and prevent air leaks. Replace if damaged, stretched, or pulled off during cycles. Confirm fit with your model.

Seals the dryer door to contain heat and prevent air leaks. Replace if torn, cracked, or causing poor drying performance. Confirm fit with your model.

Fiberglass-reinforced door seal that restores airtight closure to maintain consistent temps and reduce energy waste. Replace if torn or compressed.

Heat-resistant fiberglass gasket seals your oven door perimeter to maintain consistent temperatures. Replace when worn, frayed, or flattened to restore efficiency. Verify fit by model number.

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

Replacement dryer seal creates a tight barrier between components to prevent leaks and lint buildup. Replace when worn or brittle to stop drips. Verify fit.

Seals the coupler connection on portable dishwashers to prevent leaks at the faucet adapter. Replace when worn, cracked, or flattened to stop drips.

Seals the gap between drum and bulkhead to reduce air leaks, prevent lint buildup, and quiet operation. Replace if torn or worn. Adhesive required.

Dryer door gasket seal creates an air barrier around the door perimeter. Replace if worn, torn, or causing heat loss. Confirm fit with your model number.

Vinyl door seal lines the dryer door perimeter to block air leaks and cushion closure. Replace when worn or cracked to restore a tight seal. Verify fit by model.

Seals your dryer door to prevent heat loss and improve drying efficiency. Replace if torn, cracked, or causing air leaks. Confirm fit with your model number.