Dryer Gasket & Seal

• Noisy

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

First I watched videos about squeaking Kenmore dryers. Then I used that information to open the dryer, diagnosing the fact that the roller on the drum belt tension arm had broken and actually fallen off the arm. The dryer was filled with lint and dust/dirt, so I also saw that the seals on the dryer had deteriorated greatly. AppliancePartsPros website is outstanding, far better than its competitors. This made it easy to find the parts and videos that I needed. It took hours to pull everything... Read more

Put new seal on. Read more

I took it apart and cleaned and lubricated the rear support rollers and the belt pulley roller. I think the squealing was coming from the pulley roller. I then replaced the rear felt as it was badly deteriorated. The dryer now runs much more smoothly and quietly. Read more

Ordered new seal and the correct adhesive to use and followed directions for resealing of the door. Read more

I took the dryer apart.....first had to clean out all the lint here and there. Took the drum out, inspected the belt and back support wheels. They seemed to be fine. In the front the drum turns on two supports that have a Teflon glide. Those two glides had been worn off with their pad so metal was rubbing against metal. Went online to appliancepartspros.com and looked up on the schematic what parts I needed. I also had called around locally and the same parts cost twice as much....so I... Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

Selected and ordered parts from online drawings. Watched videos showing how to make repair. Replaced worn parts with new ones. Suggested improvement: Videos didn't show my model (I know there are many models, showing all is probably not possible). In case of Felt the video showed a Maytag dryer when my model was GE. In my case Felt had torn and dislodge from slot so I didn't know exactly how it should be installed. A simple picture of the installed Item would help. Also the parts list should... Read more

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more

Pretty easy and straight forward fix. I removed door from dryer, seperated the inner from outer door shells by unscrewing the phillip head screws. Remove the old seal and replaced with new one. Screw everything back together, verify door closes and seals properly...job done! Read more

I replaced the seals and tub bushings to bring back a quieter operation and keep from doing more damage.I have done so since it was new in 1990. It still has a lot of kife left in it. And it beats buying a new unit any day. Read more

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more