Electrolux Wall Oven Parts

I tried swapping the cables around by putting the cables from the burners that would light onto the ones that didn't light. When I did that the problem would move. So this is how i determined that the issue was with this module and not the burners or cables. Once this new module arrived it was simple to disconnect the old one and put the cables back on the new one. I tested it (holding by breath!) and then all of the burners started. HOORAY! Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

Ordered replacement parts Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

Replaced spark module - oven was less than two years old. Like a lot of new gas ovens, turning on any one burner to 'lite' sends sparks to all 5 top burners. The difficulty was getting to the spark module, as some generic videos show access to it from the upper panel on the back of the oven, but it wasn't there. Had to take off the entire top burner panel of the oven to get to the module, and then it was simple to replace the module by transferring the wires to the new one. I did see on... Read more

Bought name brand parts to match the stove brand. The fit was perfect and have never had an order arrive the next day from ordering it. Read more

• Oven is too hot
• Little to no heat when baking

Removed old thermostat and pulled old thermocouple fron oven. ran new thermocouple to oven and put in clip, tistalled new thermostat using 2 phillips head screws, done. Read more

Order the part from you all. Watched the video how to install, which was easy to understand. the part arrived A DAY EARLIER than we expected! How nice is that? and installed part, stove /oven works. everybody's happy. Read more

• Won't start

Replaced igniter and orifice assembly, and replaced spark module. Used the video for help, but the video doesn't show the top cover piece that needs to be taken off first. Also the screws for the igniter set were stuck from old grease or something and had to be drilled out. Overall the project was well worth my time for the cost vs replacement decision. AppliancePartsPros.com makes it so easy to choose a part and guesstimate the probably of choosing the right one. Read more

Replace control board. Read more

Turned off the power. Pulled out the stove. Removed back of upper part of stove. Removed old control board. Took photos with phone to make sure I got wires back on correctly. Only 1 wire was difficult to remove and required gentle rocking with pliers. Put the overlay on the new board. Placed all the clips and wires back on the new board. Turned on power to test. Tested ok. Turned power off and resecured the board and back on the stove. Repositioned the stove. Turned power back on. I... Read more

Watched the video here, took the leap that burner was the problem and ordered it. Also found another vid on you tube that was more specific to my Kenmore. Tip: find out how to take off the oven door. For mine it was very easy but not detailed in the APP vid. I followed instructions in APP vid but also first took off back panel of range and tested resistance of old burner to ensure that was truly the problem (as suggested by other YT vid). Also, dis/connecting the wires from the back is easier... Read more

I unplugged the stove ,cut the 50 amp cord off from the terminal block as it was burned took out the terminal block as it to was all melted .installed the new terminal block with a new stove cord back in business Read more

My tenant thought that the oven safety valve was bad, but after some research, I found that the transfer of heat from the igniter had to be sufficient enough to cause the valve to open.Your agent confirmed this and reassured me that even if the igniter was glowing, there was a 99% chance that it wasn't getting hot enough. I ordered the igniter, and also the safety valve just in case, as we were going to be fixing this on Christmas eve, so the oven could be used for Christmas dinner. Your agent... Read more

Ordered replacement parts Read more

Bought name brand parts to match the stove brand. The fit was perfect and have never had an order arrive the next day from ordering it. Read more