Estate Parts

Slid in new screen. Read more

Installed new agitator Read more

• Leaking

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

Remove upper and lower baskets for access. Remove 4 Torx screws holding drain/filter assembly, accessing last screw by rotating the water duct clockwise. Be sure to first un-clip the water duct at top and rear of dishwasher so that it can be moved. (Take the opportunity to remove accumulated deposits behind the water duct). Remove the drain/filter assembly and then remove the single screw holding the food chopper housing. Then remove the chopper assembly which is likely to be in pieces if it... Read more

• Will not tumble
• Takes too long to dry
• Noisy

I FOUND the website on t internet, found my part ordered it and watched the how to video ,repaired the dryer myself. Awesome Website. Read more

• Will not stop filling with water
• No hot or cold water
• Will not fill with water

Replacing the water inlet valve fixed the problem. For many months we noticed cold water was just dribbling into the washer during the rinse cycle, and "warm" washes were hot not warm. It seemed like the cold water wasn't able to enter the machine. Then one day the cycle just stopped when it reached "rinse" and wouldn't go any further. I first tried solving it by cleaning the filter where the cold water hose enters the machine at the back. It was coated in sediment (the water comes from a... Read more

• Not drying dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

• Takes too long to dry
• No heat or not enough heat

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

• Door won't open or close
• Door sweating
• Fridge too warm
• Noisy

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

We bought a new filter. Read more

• Element will not heat

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more

• Too warm
• Fridge runs too long
• Fridge too cold
• Frost buildup

A word of thanks to AppliancePartsPros - they delivered in one day. Ordered at 4PM CDT and received the part by noon the next day. Also, Alicia in the help department was able to locate an electrical diagram for my old freezer. This was essential for proper setup and her persistence in tracking down the diagram was top notch. Now on to my problem. One day I opened the freezer and found frost and thawing food. I attributed this to the door hitting an item in the freezer and not completely... Read more

• Won't start

Ordered a new thermal fuse from your website last week and installed it three days ago. This is the second fuse in one year that needed to be replaced. The dishwasher was purchased new in 2012. Relatively easy to replace. Your website had a you tube video that showed how to replace it. Power came back on the control panel, but the start button (not a button, but a touch screen) would not work. This is the second time in two years that the control panel had to be replaced because the start... Read more

• Will not drain
• Won't start
• Will not fill with water
• Lid or door will not open

My son was doing his laundry, only to announce that the washer wouldn't rinse, spin or drain. I looked on line at new washers and was staggered to see how much they cost, our Whirlpool is 20 years old! Then I looked on Craig's list to see about getting a used washer, but when I found something that looked good, and looked up how it performed, most of them had terrible reviews. So, I looked at a video that told about the 5 most common things to go wrong and figured out it was a broken lid... Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

Top mounted freezer with bottom refrigerator. Kenmore Elite Shut off the power Remove all food stuff from freezer (placed in ice chest) then shelves. Removed the ice maker, (easy!) 3 screws and unplugged wires. 2 screws in the back panel. Pulled top forward - downward Unplugged wiring harness from back wall of freezer, removed ground wire from panel Pulled fan blade off. (Fan was attached to back wall, not removable back panel) Removed 2 screws to get to fan motor. 'Unsnapped ' motor... Read more