Frigidaire Refrigerator Gasket & Seal

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. As a crucial sealing component, it works to prevent air and temperature leakage around the refrigerator door. The gasket creates an air-tight seal when the door is closed, maintaining proper cooling and preserving freshness inside.

The causes of a bad gasket can include cracks, dried-out or degraded rubber, or damage from repeated door openings and closings.

Symptoms of a bad gasket include:

• Increased humidity or moisture inside the refrigerator
• Difficulty keeping temperatures low enough
• Frost or ice build-up around the door perimeter

This OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Color: Black

The Door Gasket is an OEM part for Frigidaire refrigerators. It is designed to seal the refrigerator door tightly, preventing cold air from escaping and keeping the set temmperature inside the appliance.

A bad door gasket can be caused by wear and tear, damage, or improper cleaning. Signs of a faulty door gasket include a loose seal, condensation or frost buildup around the door, or difficulty in closing the door properly.

Symptoms of a bad door gasket can include:

• The refrigerator not maintaining its temperature.
• Excessive frost or condensation inside the refrigerator.
• A visible gap or uneven seal between the door and the cabinet.
• Difficulty in opening or closing the door.

Replace your worn or damaged door gasket with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This door gasket creates an airtight seal around your refrigerator or freezer door or lid, keeping cold air in and moisture out. Replace a worn gasket to restore temperature control, reduce frost, and support efficient operation.

• Forms a tight perimeter seal between the cabinet and door/lid to prevent air leaks
• Helps maintain stable internal temperatures and consistent cooling performance
• Reduces frost and condensation caused by a failed or leaking seal
• Common symptoms: visible tears or cracks, gaps, warping/shrinkage, door not sealing or staying closed

• Disconnect power; remove items from the door/lid as needed
• Warm the new gasket (soak in warm water or gently heat) to make it pliable, then straighten corners
• Fit the gasket into the channel or under the retainer, working evenly around the perimeter
• Check closure all around with a paper test; adjust hinges/leveling as needed and allow the gasket to relax and conform

This door gasket seals the dishwasher tub opening to prevent water leaks during the wash cycle. A fresh, pliable gasket helps maintain proper water containment and quiet operation.

• Creates a watertight seal around the dishwasher door perimeter
• Helps reduce leaks, puddling, and excessive moisture at the base of the door
• Restores proper door compression and sound dampening

• Disconnect power and turn off water supply before servicing
• Remove the old gasket from the channel; clean the groove of debris and mineral buildup
• Press the new gasket evenly into the channel, aligning the center at the top first
• Close the door to help seat the seal; check for pinches or gaps and adjust as needed

The Water Filter O-ring is an OEM replacement part for Frigidaire refrigerators. It is specifically designed to create a secure seal for the water filter, preventing leaks and ensuring that the filtration system operates effectively.

Causes for a malfunctioning Water Filter O-ring can include wear and tear from regular use, improper installation that leads to damage, or material degradation that affects its sealing capability.

Symptoms of a bad Water Filter O-ring include:

• Water leaks around the filter area
• Reduced effectiveness in water filtration
• The need for frequent filter replacements due to compromised seals
• Visible damage or wear to the O-ring

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This white door gasket seals the perimeter of the refrigerator door. It helps keep cold air in and humid air out, supporting stable temperatures and reducing frost and moisture around the door opening. What it does:

• Maintains an airtight seal between the door and cabinet
• Replaces a torn, cracked, shrunken, or deformed gasket that won't seal
• Helps address condensation around the door, frost/ice buildup, temperature fluctuations, or a door that won't close flush

• 1 door gasket (white)

• Unplug the appliance before servicing
• Warm the new gasket (soak in warm water or use low, indirect heat) to relax kinks for easier fit
• Start at the corners and work evenly around the door; on screw-retained liners, loosen screws, seat the gasket lip, then retighten
• Close the door and check the seal; smooth out waves and allow the gasket to conform over the next 24 hours

This replacement door gasket fits the refrigerator compartment. It forms a tight seal between the door and cabinet to help keep cold air in, limit moisture at the door, and maintain consistent temperatures. What it does:

• Seals the fresh food door opening to prevent air leaks
• Helps maintain stable interior temperature and humidity
• Reduces condensation and frost around the door perimeter
• Common failure signs: torn, warped, or compressed gasket; door not sealing; persistent condensation; temperature fluctuations; longer run times

• 1 refrigerator fresh food door gasket

• Disconnect power before servicing
• Lay the gasket flat to relax; gently warm with hot water or low heat to remove kinks
• Remove the old gasket; on many models, lift the liner lip or loosen retainer screws to release it
• Press the new gasket fully into the channel; check corners for a uniform seal and adjust door alignment if needed

This replacement door gasket forms the perimeter seal on the refrigerator door. It keeps cold air in and humid room air out to maintain temperature and help prevent frost and condensation when the original seal is worn or damaged.

• Creates an airtight seal between the door and cabinet
• Helps maintain proper internal temperature and reduce frost and moisture
• Resolves: visible tears, hardened or misshapen gasket, gaps at corners, or door not closing fully
• Symptoms can include condensation around the door, frost buildup, or warming in the compartment

• Unplug the appliance before starting
• Gently pull the old gasket from the retainer/channel, noting orientation
• Warm the new gasket in hot water or with gentle heat to relax creases; do not overheat
• Press the gasket lip fully into the channel, work evenly around the door, square the corners, and ensure even contact all around when closed

This gray door gasket restores a tight seal around the freezer door opening so cold air stays in and warm, humid air stays out—helping maintain proper temperature and reduce frost buildup when the original seal is worn or damaged. What it does:

• Seals the perimeter of the freezer door to prevent air leaks
• Helps minimize frost/ice accumulation and moisture around the door
• Supports consistent interior temperatures and performance
• Common signs of failure: tears, warping, gaps, frost buildup, sweating/condensation, and poor door sealing

• 1 gray door gasket

• Unplug the appliance before servicing
• Warm the new gasket (soak in warm water or gently heat) to relax folds for easier installation
• Install starting at the corners; ensure the gasket fully seats in the retainer all the way around
• After installation, check seal tension around the door; use low heat to help the gasket conform if needed

This replacement sealing gasket restores a tight, reliable seal between mating parts in your appliance. A proper seal helps prevent leaks and bypass, reduces noise, and supports overall performance and efficiency.

• Creates a compressible seal between components to prevent air or moisture bypass
• Helps maintain correct airflow/temperature containment for proper operation
• Reduces vibration and rattling caused by hardened or damaged seals
• Replace if the original is torn, flattened, brittle, missing, or leaking

• Disconnect power before servicing; shut off water supply if applicable
• Remove the old gasket and clean mating surfaces of residue/debris
• Match the original routing/orientation; do not stretch or over-compress the gasket
• Tighten fasteners evenly to ensure a uniform seal; verify no pinching or gaps

This freezer door gasket seals the door to the cabinet to keep cold air in and moisture out, helping maintain proper temperatures and reduce frost. Replace a warped or torn gasket to restore an even, reliable seal.

• Creates the perimeter seal between the freezer door and cabinet
• Helps maintain stable temperatures and efficient operation
• Reduces frost/ice buildup and condensation around the door
• Common fix for gaps, corners that won't lay flat, or doors popping open
• Replace when the gasket is torn, brittle, warped, or permanently compressed

• Disconnect power and clear items from the door before starting
• Condition the new gasket at room temperature; warming with hot (not boiling) water can help it relax
• Install starting at the corners; fully seat the gasket into the channel/under the retainer for an even fit
• Check the seal by closing on a slip of paper around the perimeter and adjust as needed

The Evaporator Cover Gasket seals the perimeter of the freezer's evaporator cover to prevent air leaks that can lead to frost, moisture, and temperature swings. Replacing a worn gasket helps restore proper airflow and consistent cooling.

• Seals the evaporator cover to the liner to maintain directed airflow and contain cold air
• Helps prevent frost or ice buildup around the cover and on nearby air passages
• Can help address symptoms like temperature inconsistencies, poor cooling, or excess moisture caused by air leaks
• Replaces a torn, flattened, or missing gasket to ensure a tight cover fit

• Disconnect power before servicing; wear cut-resistant gloves
• Remove freezer shelves/bins and the evaporator cover to access the gasket
• Clean mating surfaces; press the new gasket fully into place with no gaps or twists
• Ensure air vents are unobstructed, reinstall the cover securely, then restore power

This seal-damper is the gasket that fits around a refrigerator's air damper to help keep compartments properly separated and maintain intended airflow. Replacing a torn or compressed seal helps reduce uneven cooling and drafts. What it does:

• Seals the air damper opening to limit unwanted air exchange between compartments
• Helps maintain stable temperatures by preventing cold or warm air leakage
• Common symptom fix: reduces uneven cooling or warm spots near the damper area
• Also helps reduce excess frost or condensation that can form from persistent air leaks

• Disconnect power to the appliance before starting any repair and remove nearby food/shelves for access
• Access the damper housing per your model's service instructions, remove the old seal, and seat the new seal onto the damper frame or mounting groove
• Clean the mounting surface of debris or old adhesive so the new seal sits flat; use gentle pressure to fully engage the seal
• If the damper housing is cracked or the seal does not seat properly, replace the damper assembly.

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

Replacement refrigerator door gasket restores a proper seal around the refrigerator door to help maintain steady internal temperatures and reduce frost, condensation, and cold-air leakage. Helps keep food fresher and supports consistent cooling. What it does:

• Seals the door-to-cabinet gap to help prevent cold air from escaping and warm air from entering.
• Helps reduce frost buildup and interior condensation when the door seals correctly.
• Common replacement when the gasket is torn, deformed, flattened, or the door no longer seals tightly.
• Restores sealing contact along the full door perimeter to support temperature stability.

• Disconnect power to the appliance before attempting any repair.
• Clean and dry the door flange and gasket channel before installing to ensure a proper seal.
• Seat gasket evenly around the door; inspect for gaps and correct fit before returning appliance to service.
• Follow OEM instructions for any recommended conditioning (warming/softening) or final adjustments.

This freezer door gasket forms the airtight seal between the freezer door and cabinet. Replacing a worn or damaged seal helps keep cold air in, reduce frost buildup, and restore proper temperatures and efficiency.

• Creates a tight perimeter seal to prevent warm air leaks and moisture intrusion
• Helps maintain stable freezer temperature and humidity
• Reduces frost and ice accumulation around the door area
• Common symptoms: visible gaps or tears, door not sealing fully, condensation at the door edge, heavy frost near the door

• Disconnect power before servicing
• Warm the new gasket (soak in warm water or use gentle, low heat) to relax and ease installation; do not overheat
• Remove the old gasket; seat the new gasket fully into the door channel (some models require loosening and retightening retainer screws)
• Verify an even seal all around; perform a paper/dollar-bill test and adjust corners as needed