General Electric Dryer Parts

Fix a dryer that won't start, has flashing cycle lights, or runs without stopping. This electronic control board restores normal cycle operation.

Replacement screw that secures dryer panels, trims, and internal components. Needed when original fasteners are missing, stripped, or corroded.

This is a cycling thermostat that monitors the temperature inside the dryer drum and signals the heating element to turn on and off to maintain the selected drying temperature. It is typically mounted on the blower housing or exhaust duct. Replace this part if your dryer is not heating, overheating, running too hot or too cool, or if clothes are taking too long to dry.

Replacement center screw that secures the control knob to the shaft on your dryer. Needed when the original screw is stripped, missing, or loose.

Fixes unresponsive or stuck control panel buttons on your dryer. This push-button switch restores reliable operation when buttons fail to engage functions.

Fix a dryer that won't start, advance, or complete cycles with this electromechanical timer. Controls cycle selection and timing. Moderate DIY repair.

Dryer won't start or has no power? This electronic control board manages dryer cycles and settings. Straightforward replacement restores function.

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.

This electromechanical timer assembly controls cycle timing for compatible GE ranges and ovens, restoring accurate cook cycles and timer functions. It replaces a worn or non-advancing control to help your appliance complete timed operations reliably. What it does:

• Advances and times cooking cycles so bake, broil and self-clean operations run to completion
• Restores timer and manual cycle control when the original timer stops advancing
• Helps resolve symptoms like no timer display, oven cycles that won't start or stop on schedule, or intermittent timing failures
• Works as the user-accessible timing control for front-panel settings

• Disconnect power to the appliance before beginning service to avoid shock hazard
• Access may require removing the range/oven control panel or console; keep fasteners and trim for reassembly
• Handle connectors carefully and match wiring/location during reinstallation

Secures the rear drum bearing to keep your dryer drum aligned and rotating smoothly. Replace if bracket is cracked, bent, or worn to restore proper support.

Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.

This control component allows selection of different heat settings and is located on the dryer's control panel. Replace it if you can't select certain temperature settings, the dryer runs too hot or cold, or the switch feels loose or unresponsive.

This is a flexible seal that fits around the dryer door opening to prevent heated air from escaping the drum during operation. It creates an airtight barrier between the door and the dryer cabinet to maintain proper drying temperatures. Replace this gasket if you notice heat leaking from around the door, clothes taking longer than normal to dry, or the seal appears cracked, torn, or flattened.

This is a mechanical timer that controls the duration and sequence of drying cycles in your dryer. It advances through the selected cycle, activating the motor, heater, and cool-down periods at the appropriate times. Replace this timer if your dryer won't start, won't advance through cycles, runs continuously without shutting off, or stops mid-cycle.

Side vent kit for dryers with exterior vent trim and mounting interface. Replaces damaged, missing, or worn vent trim to restore side vent openings.

This roller support holds the dryer drum roller in place to help the drum turn smoothly and stay aligned. Replacing a worn support can reduce noise and wobble and help protect the belt and drum from uneven wear. What it does:

• Holds and positions the drum roller so the drum rotates with minimal friction
• Keeps drum alignment and belt tracking stable during operation
• Helps prevent drum wobble and uneven wear that can lead to rubbing or thumping noises
• Common symptoms: loud squealing or grinding, thumping during rotation, visible drum wobble

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer front or rear panel; follow the model's service manual
• Inspect the roller, axle, and adjacent support components; replace any worn parts to prevent repeat failure
• Use proper tools and secure fasteners to factory torque