General Electric Dryer Parts

Replaces the rear mounting bracket that secures a leveling leg to your dryer frame. Needed when the original bracket is cracked, broken, or missing.

Steam generator assembly for dryers with steam-refresh cycles. Installs inside cabinet to heat and release steam. Replace if cracked, leaking, or damaged.

Secures the door guide strip to your dryer frame, keeping the door aligned. Replace this nut if it's missing, stripped, or worn to restore proper fit.

A threaded foot assembly located at the bottom corners of the refrigerator that allows height adjustment for proper leveling. Replace when the refrigerator rocks, doors don't close properly, or the foot mechanism is damaged or stripped.

This is a hot surface glow bar igniter used in gas dryers to ignite the burner flame. It heats up until it reaches the temperature needed to open the gas valve and light the burner. Replace this part if the dryer runs but produces no heat, takes excessively long to dry clothes, or if the igniter glows but fails to ignite the gas.

This display assembly powers and visually reports the appliance control status so you can see settings and feedback on the control panel. It restores readable on-screen information and enables the front-panel display functions. What it does:

• Replaces the control-panel LCD and power/display electronics so the screen lights and shows information again
• Commonly used when the display is blank, dim, flickering or showing garbled characters
• Resolves unresponsive or intermittent front-panel display behavior tied to the display module
• Interfaces with the main control board to present time, temperature, and mode/status readouts

• One complete display assembly (power/LCD) as shown

• Disconnect power to the appliance before beginning any work to avoid shock
• Handle the LCD and cable connectors carefully to avoid damage; flexing or scratches can affect operation
• Access typically requires removing the control console or console bezel—keep track of screws and fasteners
• If symptoms persist after replacement, test the main control board and wiring harness for faults

Housing cover that protects and encloses the dryer heating element assembly. Replace if cracked, broken, or damaged to restore proper dryer operation.

Replacement rear panel for dryers. Restores the cabinet's back surface when the original is dented, rusted, cracked, or damaged. Secures and protects internal wiring and components.

Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.

Secures and aligns the rear panel on your dryer. Replace this screw if the back housing is loose, missing, or stripped to restore proper panel fit.

Dryer overheating or shutting off? This safety thermostat detects excessive heat and cuts power to prevent thermal damage. Direct replacement part.

If your dryer won't advance through cycles or stops mid-cycle, the mechanical timer may have failed. This part restores cycle selection and timing control.

This timer is the electromechanical control that sequences a washer's wash, rinse and spin cycles, restoring proper cycle advancement and timing for affected machines. Use this direct-fit replacement to regain reliable cycle control and predictable operation. What it does:

• Rotates through and switches washer cycle stages (fill, agitate, drain, spin) to control timing
• Replaces a worn or failed timer that causes cycles to stop, not advance, or skip functions
• Restores timed operation when a washer won't complete cycles or starts intermittently
• Interfaces with controls and motors to coordinate cycle transitions

• Disconnect power before attempting service to avoid shock or injury
• Access may require removing the control panel or console
• Retain all mounting hardware and note wiring positions; replace exactly as removed

This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does

• Secures panels, brackets, and small components to the appliance frame
• Restores proper alignment and helps eliminate rattling or vibration
• Replaces missing or stripped fasteners that prevent parts from staying fixed
• Matches OEM fit for reliable fastening where the original screw was used

• One replacement screw

• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Tighten snugly but avoid overtightening to prevent thread damage
• Keep removed hardware organized so you can install replacements in the original locations

Size: 8-18 x 7/8 inch.

Door hinge for dryers. Attaches the door to the dryer cabinet frame, allowing it to open and close smoothly. Replace if cracked, broken, or worn.