General Electric Refrigerator Cap Or Cover

This grille sensor is the temperature-sensing probe that monitors heat in the appliance grille area to help controls regulate cooking temperature and safety features. It provides accurate feedback so the oven or grill can maintain set temperatures. What it does:

• Senses temperature in the grille/grill area and sends readings to the control board
• Helps the appliance maintain consistent cooking or broiling temperatures
• Can cause temperature-related errors or inconsistent heating when failed
• Common symptom: oven or broil function runs too hot, too cool, or shows error codes related to temperature sensing

• One grille sensor

• Disconnect power to the appliance before any service to avoid shock or injury
• Handle the sensor carefully; avoid bending or contaminating the sensing tip
• Route and secure the sensor wiring as OEM designed to prevent heat or pinch damage

This hinge cover replaces the plastic trim that snaps over the refrigerator door hinge to restore appearance and protect the hinge area from dust and dings. Fits the bisque/color-matched hinge opening for a clean finish. What it does:

• Covers and protects the door hinge housing from dirt, moisture, and everyday wear
• Restores cosmetic appearance where a chipped or missing cover exposes the hinge
• Helps prevent accidental contact with hinge hardware for safer daily use
• Matches bisque-colored trim so the door looks factory-original

• One hinge cover (bisque) as shown

• Unplug the appliance or turn off power at the breaker before servicing if work near electrical components is required
• Support or stabilize the door before removing hinge trim to avoid door movement
• Typically snaps into place or secures with the original fasteners; keep existing screws/clips and reuse if present

This cover fits over the refrigerator auger motor to protect internal components and help guide ice through the dispenser. It keeps the motor area enclosed to reduce debris intrusion and supports smooth auger movement. What it does

• Protects the auger motor and gearbox from ice, frost, and debris
• Helps guide ice from the bin into the auger for consistent dispensing
• Common symptom: reduced or intermittent ice dispensing, unusual noises from the dispenser area

• One cover

• High-level replacement — remove power to the refrigerator before starting
• Handle components gently to avoid damaging the auger or wiring
• If the auger still doesn't turn after replacement, check the motor, wiring, and control components

This mullion duct cap closes and protects the end of the refrigerator mullion air duct, helping maintain directed airflow and a finished appearance on the door jamb. It replaces a cracked or missing end cap to reduce drafts and keep the duct sealed. What it does:

• Caps and protects the open end of the mullion air duct to preserve airflow routing
• Helps prevent air leakage that can contribute to uneven cooling or frost buildup near the door
• Restores a clean, finished look to the door mullion area
• Keeps debris and moisture out of the duct to reduce odors and buildup

• One mullion duct end cap

• Disconnect power to the appliance before beginning any work
• Typically installs by snapping or sliding into the duct end; use moderate force and avoid prying with metal tools
• Inspect surrounding trim and fasteners and replace any damaged clips as needed

This component is an evaporator cover assembly for refrigerators. At the back of the refrigerator, there is an evaporator that covers the fresh food compartment. This assembly includes the cover and the connected parts, including the fan. A sign that the evaporator is not working properly is if there is an ice build-up. Food may begin to go bad faster when the evaporator is not functioning correctly. If the fan itself is going bad, it may make loud humming noises. Unplug the appliance before replacing this part. While replacing this part, it's a good idea to keep any fresh food in a temperature safe location while the power is off. Wear gloves for safety from cold temperatures and any sharp objects.The evaporator cover assembly and its included parts are compatible with refrigerators that are manufactured by GE. This assembly is sold individually. It is sourced straight from the manufacturer.

This plug cover and gasket assembly provides the replacement cover and sealing gasket for the appliance electrical access area, restoring a secure fit and helping keep out moisture and debris. It's a direct-fit replacement designed to restore proper coverage. What it does:

• Covers and protects the appliance's electrical plug/access opening to prevent exposure to wiring and terminals
• Gasket creates a seal to help keep out moisture, dirt and cooking residues
• Restores a snug, stable fit where a cracked or missing cover allowed movement or gaps
• Helps reduce risk of corrosion or shorting from contaminants reaching components

• One plug cover and gasket assembly

• Always disconnect power before accessing electrical components
• Remove only the fasteners securing the old cover; note orientation of the gasket for correct reinstallation
• Inspect mounting area and wiring for damage before installing the new part
• Use basic hand tools;

The MWF Bypass is an OEM replacement part for GE refrigerators. Located within the bottom freezer compartment, the metal water filter bypass fitted assembly is responsible for directing filtered or unfiltered water flow to the ice maker and dispenser.

Causes for replacement may include faulty diverter components obstructing water flow to selections or resulting in water leaks.

Symptoms of a problematic bypass unit include:

• Inability to select filtered or unfiltered water from the dispenser
• Ice maker failure due to lack of water or poor water quality
• Mineral deposits accumulating on internal parts from unfiltered water

This OEM replacement bypass is compatible with GE, Hotpoint, and Profile model refrigerators.

This access cover closes a service opening on the refrigerator cabinet, protecting internal components and restoring a secure, finished fit. Replacing a cracked or missing cover helps keep debris out and supports proper operation and airflow paths.

• Covers the machine/service compartment to shield wiring, fan, and other components from contact and debris
• Helps maintain designed airflow through the compartment when properly installed
• Reduces vibration and rattling when the cover is secured
• Replace if the cover is missing, cracked, warped, or no longer fastens securely

• Disconnect power before servicing
• Remove any retaining screws/clips and note the cover's orientation and vent/slot alignment
• Transfer any original grommets or insulation to the new cover if present
• Reinstall with existing hardware; do not overtighten; ensure openings/vents remain unobstructed

This is a replacement cover for the refrigerator dispenser bucket that restores the dispenser opening and helps contain and direct dispensed contents for cleaner operation and improved appearance. What it does:

• Replaces a cracked, broken, or missing dispenser bucket cover that can let ice or water escape
• Helps guide dispensed items into the cup or container to reduce spills
• Restores a finished look to the dispenser area
• Prevents debris from entering the dispenser bucket

• One dispenser bucket cover

• Disconnect power to the appliance before beginning any repair
• Typically installs by aligning and snapping into place or securing with the original fasteners; retain any removed clips or screws for reassembly
• Handle plastic parts carefully to avoid cracking during installation