General Electric Refrigerator Gasket & Seal

This rear gasket cover secures the refrigerator door gasket and helps maintain a clean seal at the back edge of the door. It restores proper gasket alignment and helps reduce air leaks and moisture buildup. What it does:

• Holds the rear edge of the door gasket in place for a consistent seal.
• Helps prevent cold air loss and condensation by keeping the gasket aligned.
• Reduces rubbing and wear on the gasket edge caused by movement.
• Commonly replaced when the cover is cracked, missing, or allows the gasket to pull loose.

• One rear gasket cover.

• Remove power to the appliance before beginning any work.
• Typically installs by snapping or sliding into the door gasket channel; inspect surrounding trim for damage.
• Use basic hand tools; avoid forcing the cover to prevent breaking the part or the door.
• If gasket damage is present, replace the gasket as needed to ensure a proper seal.

This front-chill seal is the replacement gasket that seals the refrigerator's front chill/drawer area to help maintain proper temperature and reduce moisture intrusion. Restores a tighter seal to improve cooling performance in the drawer area. What it does

• Replaces worn, torn or compressed front chill/drawer gasket that lets cold air escape
• Helps maintain even temperature in the chill/deli drawer and reduce frost buildup
• Reduces moisture and odor transfer between compartments caused by a failing seal
• Common symptom: drawer not staying cold or visible gaps around the drawer edge

• Designed for a direct-fit replacement; remove the drawer or access panel as needed to reach the gasket
• Clean the mounting flange and channel before installing the new seal for best adhesion/seating
• Seat the gasket evenly into the channel; use gentle, even pressure to avoid distortion
• Disconnect power before removing panels or working near refrigeration components

This mullion duct gasket seals the vertical door/mullion area to help keep cold air inside the refrigerator and reduce condensation. It replaces a worn or damaged gasket to improve seal performance and reduce moisture buildup. What it does:

• Seals the mullion/duct area between doors to help maintain proper temperature and reduce warm air infiltration
• Helps prevent condensation and frost build-up along the door mullion
• Restores the door seal where gaps or deterioration allow air leaks
• Works with original mullion/duct trim to maintain proper airflow paths

• 1 mullion duct gasket

• Designed to fit into the mullion/duct channel; remove old gasket and press new gasket into place
• Handle gently to avoid stretching or tearing the gasket during installation
• Clean the mounting channel before installing to ensure a full contact seal
• Disconnect power or follow appliance safety guidelines before servicing doors/mullion area

This side gasket seals the chill compartment, helping maintain proper temperature and reduce frost and moisture buildup for consistent food storage. It replaces worn or torn side seals to restore the compartment's closing surface. What it does:

• Replaces damaged or hardened side seal material to improve the compartment's seal.
• Helps reduce air leaks that can cause temperature fluctuations or excess frost.
• Supports efficient cooling by maintaining a tighter seal around the chill area.
• Can resolve symptoms like cold loss in the chill compartment, visible gaps, or condensation/frost near the seal.

• High-level swap: remove the old seal, clean the mounting surface, and press the new seal into the channel until fully seated.
• Use mild soap and water to clean surfaces; avoid harsh solvents that can damage plastic.
• If adhesive or fasteners are present, retain or replace them per the model's instructions.
• Disconnect power only if required by your model's service instructions; follow all safety guidance.

This self-adhesive foam strip seals gaps to help block drafts, reduce moisture intrusion, and improve temperature retention. It's a simple replacement that helps restore a proper seal where foam padding has worn or separated. What it does:

• Provides a compressible seal along edges and contact surfaces to reduce air leaks
• Helps prevent frost build-up and condensation by maintaining an even seal
• Cushions panels and reduces rattles or vibration where foam padding is missing
• Restores contact where existing foam is cracked, compressed, or detached

• Clean and dry the mounting surface thoroughly before applying for best adhesion
• Measure and trim the strip to fit; remove backing and press firmly into place
• Replace only when foam is worn, torn, or no longer seals effectively
• For safety, unplug the appliance or turn off power when working near electrical components

This front pan cover gasket seals the refrigerator's drain pan cover to help keep water and debris contained, reducing odors and preventing leaks under the appliance. It replaces a worn or cracked gasket for a cleaner, more reliable seal. What it does:

• Seals the front edge of the evaporator/drip pan cover to help direct condensate into the drain channel
• Helps prevent water from leaking or pooling beneath the refrigerator
• Reduces the chance of debris and odors collecting around the drain pan area
• Commonly replaced when the existing gasket is cracked, loose, or no longer seats properly

• Install with the refrigerator unplugged or power turned off to avoid electrical hazard
• Remove the pan cover, clean mating surfaces, and press the gasket into the channel until fully seated
• Inspect the pan cover and surrounding components for damage; replace any cracked parts
• No special tools required for most models; use care to avoid pinching or stretching the gasket