General Electric Refrigerator Gasket & Seal

This inlet meat pan gasket seals the meat pan/deli drawer area to help maintain proper compartment airflow and reduce moisture and odors. It restores a tighter seal for more consistent internal temperatures and fresh storage. What it does:

• Replaces a worn or torn inlet gasket that lets air leak around the meat/deli pan
• Helps reduce moisture buildup and frost near the drawer area
• Can improve temperature consistency inside the deli/meat compartment
• Reduces food odors caused by gaps in the seal

• One inlet meat pan gasket

• Disconnect power to the appliance before starting any repair
• Remove the drawer/pan to access and clean the gasket seating area prior to install
• Press the gasket fully into its channel, ensuring an even, continuous seal around the opening
• Inspect for proper fit and reassemble drawer; check drawer operation and seal after reinstall

This louver gasket seals the refrigerator/freezer louver to help direct airflow and keep the cabinet edge sealed from drafts and debris. It restores a proper seal to improve cooling consistency and reduce dust buildup around the louver opening. What it does:

• Replaces worn or torn louver sealing to restore a tight edge seal
• Helps maintain directed airflow through the lower louver/vent area
• Reduces drafts and keeps dust and debris from entering the cabinet gap
• Addresses visible gaps, flapping rubber, or airflow noise near the louver

• High-level replacement: typically removes and snaps into the louver channel or secures with retained clips; inspect alignment before final seating
• Use gentle, even pressure to avoid tearing the gasket; trim only if manufacturer specifies
• Disconnect power to the appliance or ensure the unit is powered down when working near electrical components
• If adhesive or fasteners are present, remove old residue and use only OEM-recommended adhesive or hardware

This AHU Chill seal is a replacement gasket designed to help maintain proper temperature control and airflow in the chilled compartment. It restores a tight seal to reduce warm-air leaks and help the appliance run more efficiently. What it does:

• Replaces a worn or damaged chill compartment gasket to restore an airtight seal
• Reduces warm air infiltration that can cause frosting or inconsistent temperatures
• Helps the cooling system maintain set temperatures and reduces run time caused by leaks
• Fits where the AHU/chill compartment requires a dedicated perimeter seal

• One AHU Chill seal (gasket) as shown

• Remove old gasket and clean mating surfaces before installing the new seal
• Press the gasket into the channel evenly; avoid stretching or twisting the seal
• Check the seal for uniform contact and adjust as needed; replace damaged retainers if present

This self-adhesive foam strip seals gaps and cushions components to reduce drafts, noise, and moisture intrusion—helpful for restoring proper airflow and improving efficiency where foam padding or gap sealing has deteriorated. What it does:

• Provides a soft seal to close small gaps and prevent air leaks
• Cushions panels to reduce vibration and rattling noises
• Helps limit moisture and dust entry around seals and components
• Supports consistent temperature by reducing unwanted airflow

• Clean and dry the mounting surface before applying for best adhesion.
• Trim to length with scissors or a utility knife; press firmly to set adhesive.
• Avoid stretching the foam while applying; allow adhesive to set 24 hours for full bond.
• If near electrical components, disconnect power before working and avoid covering vents.

A replacement damper gasket that seals the refrigerator air/damper assembly to help maintain proper airflow and temperature control inside the fresh-food compartment. Restores the damper seal to reduce drafts and energy loss. What it does:

• Creates an airtight seal around the air damper to keep conditioned air inside the compartment
• Helps the damper regulate airflow for more consistent temperatures
• Can reduce frost buildup and limit warm-air leaks that cause the compressor to run more
• Common symptom: uneven temperatures or a draft near the damper area

• One damper gasket

• Disconnect power to the appliance before beginning any service
• Remove the damper housing or inner liner trim as needed to access the gasket; handle plastic parts gently to avoid cracking
• Seat the gasket fully in the damper groove and reassemble components in reverse order

This damper gasket seals the refrigerator air damper opening between the freezer and fresh food compartments to prevent air leaks and help maintain stable temperatures. A new seal supports proper airflow and helps reduce moisture or frost near the damper. What it does:

• Seals the perimeter of the air damper/baffle to prevent bypass air leaks
• Helps regulate airflow from freezer to refrigerator for consistent cooling
• Wear, flattening, or tears can lead to warm spots in the fresh food section
• May also contribute to condensation, frost, or whistling/draft at the damper cover

• 1 damper gasket

• Unplug the refrigerator before servicing
• Remove the interior damper cover/grille to access the damper; note gasket orientation
• Seat the new gasket evenly around the damper frame without stretching or twisting
• Reinstall cover, restore power, and verify airflow and door sealing

Flexible front door seal (gasket) that restores a tight closure between the appliance door and cabinet to help maintain interior temperature and reduce moisture, frost and energy loss. Use when the existing seal is cracked, torn or no longer seals fully. What it does:

• Creates an airtight seal around the door to keep cold air in and warm, moist air out.
• Helps reduce frost build-up, water or ice between compartments, and visible condensation.
• Supports consistent internal temperatures to protect food and improve efficiency.
• Common symptom: visible gaps, a torn or deformed gasket, or cold loss around the door edge.

• Disconnect power or unplug the appliance before service.
• Remove food and any removable door shelves or bins that obstruct access.
• Clean and dry the door sealing surface before fitting the new gasket for best contact.
• Fit the gasket starting at a corner and work around the door; gently warm stiff seals to make them more pliable if needed.

This rear gasket cover secures the refrigerator door gasket and helps maintain a clean seal at the back edge of the door. It restores proper gasket alignment and helps reduce air leaks and moisture buildup. What it does:

• Holds the rear edge of the door gasket in place for a consistent seal.
• Helps prevent cold air loss and condensation by keeping the gasket aligned.
• Reduces rubbing and wear on the gasket edge caused by movement.
• Commonly replaced when the cover is cracked, missing, or allows the gasket to pull loose.

• One rear gasket cover.

• Remove power to the appliance before beginning any work.
• Typically installs by snapping or sliding into the door gasket channel; inspect surrounding trim for damage.
• Use basic hand tools; avoid forcing the cover to prevent breaking the part or the door.
• If gasket damage is present, replace the gasket as needed to ensure a proper seal.

This front-chill seal is the replacement gasket that seals the refrigerator's front chill/drawer area to help maintain proper temperature and reduce moisture intrusion. Restores a tighter seal to improve cooling performance in the drawer area. What it does

• Replaces worn, torn or compressed front chill/drawer gasket that lets cold air escape
• Helps maintain even temperature in the chill/deli drawer and reduce frost buildup
• Reduces moisture and odor transfer between compartments caused by a failing seal
• Common symptom: drawer not staying cold or visible gaps around the drawer edge

• Designed for a direct-fit replacement; remove the drawer or access panel as needed to reach the gasket
• Clean the mounting flange and channel before installing the new seal for best adhesion/seating
• Seat the gasket evenly into the channel; use gentle, even pressure to avoid distortion
• Disconnect power before removing panels or working near refrigeration components

This mullion duct gasket seals the vertical door/mullion area to help keep cold air inside the refrigerator and reduce condensation. It replaces a worn or damaged gasket to improve seal performance and reduce moisture buildup. What it does:

• Seals the mullion/duct area between doors to help maintain proper temperature and reduce warm air infiltration
• Helps prevent condensation and frost build-up along the door mullion
• Restores the door seal where gaps or deterioration allow air leaks
• Works with original mullion/duct trim to maintain proper airflow paths

• 1 mullion duct gasket

• Designed to fit into the mullion/duct channel; remove old gasket and press new gasket into place
• Handle gently to avoid stretching or tearing the gasket during installation
• Clean the mounting channel before installing to ensure a full contact seal
• Disconnect power or follow appliance safety guidelines before servicing doors/mullion area

This side gasket seals the chill compartment, helping maintain proper temperature and reduce frost and moisture buildup for consistent food storage. It replaces worn or torn side seals to restore the compartment's closing surface. What it does:

• Replaces damaged or hardened side seal material to improve the compartment's seal.
• Helps reduce air leaks that can cause temperature fluctuations or excess frost.
• Supports efficient cooling by maintaining a tighter seal around the chill area.
• Can resolve symptoms like cold loss in the chill compartment, visible gaps, or condensation/frost near the seal.

• High-level swap: remove the old seal, clean the mounting surface, and press the new seal into the channel until fully seated.
• Use mild soap and water to clean surfaces; avoid harsh solvents that can damage plastic.
• If adhesive or fasteners are present, retain or replace them per the model's instructions.
• Disconnect power only if required by your model's service instructions; follow all safety guidance.