General Electric Refrigerator Handle

This part is an upper tail handle. This is a genuine OEM part made by General Electric and has been sourced directly from the manufacturer. This part is intended to replace a broken or detached upper tail handle on multiple different models and brands of refrigerators. This upper tail handle attaches to the outside of the refrigerator and forms the handle used to open the door. A detached or faulty tail handle can prevent the door from functioning properly. If the tail handle becomes detached, opening and closing the door can be difficult. Always ensure the appliance is disconnected from its power source before attempting any repairs. Proper tools are needed to install this part and protective gloves should be worn. For more accurate installation information on how and where to install this replacement upper tail handle, refer to the original manufacturer diagrams or owner's manual.As an authentic replacement part, this upper tail handle is suitable for use on various models of refrigerators manufactured by General Electric and Hotpoint. Please note that this is a genuine part made of high-quality and durable plastic and is sold individually.

This tail handle is the replacement end piece for a refrigerator door handle assembly, restoring a finished grip and proper handle fit. It helps maintain a secure, comfortable hold and keeps the door handle aligned. What it does:

• Replaces a cracked, broken or missing tail/end piece on a refrigerator door handle
• Restores proper fit and finish so the handle sits securely and functions normally
• Helps eliminate looseness, wobble or sharp edges caused by a damaged tail piece
• Matches OEM shape to maintain original handle appearance

• One tail handle piece as shown

• High-level installation: access the door handle ends, remove any retaining screws or clips, swap the damaged tail piece for the replacement, and reassemble
• Use basic hand tools; avoid over-tightening fasteners to prevent cracking
• If the handle is painted or scratched, handle replacement part carefully to avoid surface damage
• Disconnect power only if working near electrical components or lights; otherwise no electrical disconnection is typically required

This small door handle assembly (22 in) replaces a damaged or worn refrigerator/freezer door pull to restore a secure grip and smooth opening. Fits inline with factory trim for a clean, original appearance. What it does:

• Replaces a broken, cracked or missing small door handle to restore safe gripping and door access.
• Stops wobbling or loose handles that affect door opening and closing.
• Matches factory trim finish to maintain original look and feel.

• Disconnect power and empty the door area before beginning any repair.
• Remove retaining screws or clips from the inner door panel to access the handle fasteners.
• Align handle to mounting holes, then secure with the original hardware; do not overtighten to avoid cracking.

This handle cap is the replacement end cap that finishes and secures a refrigerator door handle, restoring a clean, finished look and helping keep the handle seated. Durable molded finish matches the original part. What it does

• Covers and secures the exposed end of a door handle for a finished appearance
• Helps keep the handle properly seated and aligned during normal use
• Replaces cracked, chipped, or missing end caps that affect appearance and fit
• Restores a clean seal against dirt and moisture at the handle end

• High-level, no-specialty tool install: typically snaps or screws into the handle end; inspect fasteners before reassembly
• Work with the door open and supported; avoid pinching fingers when seating the cap
• If access to electrical components is required during disassembly, unplug the appliance or disconnect power before starting
• Do not force parts; verify correct orientation and seating to prevent damage

This tail handle is the replacement tail piece for a refrigerator door handle assembly, restoring a secure grip and proper door operation. It helps refresh worn or broken handle ends without replacing the full handle assembly. What it does:

• Replaces a damaged or cracked tail piece on the refrigerator door handle
• Restores a solid grip and proper alignment of the handle
• Helps stop rattling or looseness caused by a broken tail section
• Useful when the main handle is intact but the tail end is worn or broken

• One tail handle tail piece

• Basic hand tools typically required; handle with care to avoid scratching door finish
• Keep power off/unplug appliance only if working near electrical components or lights
• If fasteners or clips are missing, replace with OEM-specified hardware

This replacement tail handle restores a clean, secure grip to side-by-side refrigerator doors. It replaces a cracked, broken or missing tail handle so doors are easier to open and look factory-fresh again. What it does:

• Replaces damaged or missing tail handle on compatible side-by-side refrigerators
• Provides a secure grip for opening the refrigerator door
• Restores original appearance and alignment at the handle area
• Helps prevent further cabinet or door-edge wear from makeshift pulls

• Disconnect power to the appliance before starting any repairs
• Removal typically requires loosening fasteners or clips at the handle area; keep all screws and small parts
• Handle replacement is usually a straightforward repair but may require two people for larger doors