General Electric Refrigerator Screws, Nuts, Washers

This screw handle secures an appliance handle to the door or panel, restoring a stable, properly aligned grip. It's a direct-fit replacement designed to stop handle wobble and keep the handle firmly attached during normal use. What it does

• Fastens the appliance handle to the door or access panel.
• Stops handle movement, wobbling, or shifting when pressure is applied.
• Helps restore safe, stable operation when the original screw or fastener is stripped or missing.
• Works with the original handle and mounting hardware when in good condition.

• Disconnect power to the appliance and follow all safety precautions before starting.
• Use the correct screwdriver or bit to avoid stripping the head.
• Thread carefully and tighten until snug; avoid over-tightening which can crack trim or strip threads.
• If surrounding hardware is damaged or the handle still moves, inspect the handle and mounting bracket for wear.

This screw handle trim replaces the small decorative cover that hides and secures the mounting screw on a range/oven handle, restoring a finished look and preventing debris buildup around the screw. What it does:

• Covers the handle mounting screw and provides a clean finished appearance
• Helps keep crumbs and grease out of the screw cavity
• Stops a loose or missing trim from catching on clothing or hands
• Restores cosmetic look after handle removal or damage

• One screw handle trim

• Safety first: unplug the appliance or shut off power to the range before working
• Remove the handle screw, fit the trim over the screw area, then reinstall and tighten the screw securely (do not overtighten)
• Use the correct screwdriver and avoid forcing the trim; check alignment before final tightening
• If the original mounting hardware is damaged, replace it with OEM hardware

Shoulder pan head screw for refrigerator assembly and internal component mounting. Replace if screw is stripped, missing, or damaged during maintenance.

This screw tap is a single sheet-metal/self-threading fastener used to secure appliance panels and small components. It provides a reliable hold where a standard nut or pre-tapped hole is not available. What it does:

• Forms or cuts mating threads as it is driven into thin metal or plastic panels
• Secures trim pieces, brackets, and small assemblies to the appliance frame
• Helps stop rattling or loose panels caused by missing or damaged fasteners
• Works in repair situations where replacing a tapped insert isn't practical

• Use the correct screwdriver or bit to avoid stripping the head
• Drive slowly and straight; stop if resistance changes to avoid cracking plastic
• Do not overtighten — excessive torque can strip formed threads
• Disconnect power and follow appliance safety procedures when working near electrical components

This screw cap covers the exposed handle screw to restore a finished appearance and help protect the fastener from moisture and debris. It's a simple cosmetic replacement that keeps the handle area looking clean. What it does:

• Covers an exposed handle screw for a neat, finished look
• Helps reduce moisture and dirt contact with the screw head
• Replaces cracked, broken, or missing caps that leave screws visible
• Prevents minor snagging on the handle area from a bare screw head

• Inspect the handle and screw area; replace only if the cap is missing, cracked, or worn
• Typically snaps into place over the screw head; remove the old cap with a flat plastic tool if needed
• Press the new cap firmly until it clicks; ensure it's seated flush
• For safety, unplug the appliance or turn off power to the area before working in tight spaces

This is a specialty trim screw used to secure exterior trim and small appliance components. It provides a low-profile, secure fastening that helps keep panels and trims aligned and stable. What it does:

• Secures trim pieces, bezels or small panels to the appliance chassis
• Helps prevent rattles or loose panels that can occur with worn or missing fasteners
• Restores correct fit and finish after repairs or panel replacement
• Works where a shorter, specialty head screw is required for clearance

• Remove power to the appliance before beginning any repair that requires panel removal
• Use the correct screwdriver bit to avoid stripping the head
• Replace only the exact screw(s) specified for the location to ensure proper fit
• Replace all matching screws for uniform fit

Hardware kit with 12 mounting screws for refrigerator assembly and component installation. Replace missing, stripped, or corroded screws during repairs.

This is a hinge mounting screw designed to secure appliance door hinges to the cabinet or door, restoring proper alignment and stable operation. Durable replacement to fix loose or shifting hinges and reduce noise. What it does:

• Secures the door hinge assembly to the cabinet or door frame for stable door movement
• Restores proper door alignment when a missing or stripped hinge screw causes sagging
• Helps eliminate rattling or looseness at the hinge area
• Works where the OEM hinge fastener is required for correct fit and operation

• Turn off and unplug the appliance before starting any repair that requires removing panels or accessing electrical components
• Use the proper screwdriver or socket to avoid stripping the screw head
• Replace only the matching OEM screw(s); do not overtighten—secure snugly to avoid stripping threads
• If hinge threads are damaged, inspect hinge and mounting area; thread repair or hinge replacement may be required