General Electric Wall Oven Parts

Very easy fix. Turned of power at breaker. Removed oven door by lowering two "keepers" on the hinges for the oven door and sliding the door out of the oven. Removed the trim plate at bottom of oven by pushing it up.. Removed 2 screws that mount to the frame of the cabinet at the bottom that the trim plate hangs from. Then removed 4 screws that hold the oven into the cabinet at either side of the oven. Put two 5 gallon buckets in front of the oven and slid the oven out onto the side-by-side... Read more

Took apart the door to clean all surfaces of the glass front, cleaned oven absent of racks, and replaced old racks with shining new ones. She proclaimed it was 1000% better! Read more

First watched youtube instruction video. Ordered gasket. Delivered in 2 days. Removed old gasket and replaced with new in about 15 minutes. Wife happy. Read more

I replaced the main control unit Read more

Replace magnetron. Took longer to remove and disassemble m/w than to replace part. Above range installation. M/w was heavy- be careful. Read more

The oven control panel went in easily -- 4 screws to get access to it and four more to replace it. the panel does not include the face plate surface, but the existing plate can be removed from the control panel using a butter knife and re-used on the new panel. it holds on to enough of the stickiness. Read more

Very simple to fix this problem and took only a few minutes. Appliance Parts Pros has the best delivery service. I ordered the part about 2pm and the part was delivered at 11am the next morning. I live in the Atlanta area so delivery is probably faster than other areas but they always ship the same day if the order is placed before 5pm. I have used App Parts Pros several times over the last 5 years and have always been very satisfied with the service and the parts. Read more

Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more

I first called a GE service tech in to diagnose the problem. He said very quickly that the oven circuit board had a fault in it. He said it would cost $ 563. to replace. I asked him if he thought I was a fool or an idiot? Of course he didn't get the job. Before the Tech came I looked up this problem on Appliance Parts Pros.Com and found the same problem. The fix was a new oven circuit board at $163. including S&H. I ordered,after the tech left, the part and received it in 2 days. When my wife... Read more

I replaced both the Magnetron and the high voltage diode. I now have a fully functional microwave. I received the parts on time and the quality was good. I would use appliance parts pro's again. Read more

The F9 error code is supposed to indicate that the door lock mechanism has failed. My oven would give the F9 code and turn off during normal baking at 400 F after about 30-40 minutes. It turns out that GE must have programmed the error codes incorrectly in my model, because the real problem was that my control board cooling fan was no longer functional, and one of the two thermal switches was shutting off the unit when the control board area got too hot. AppliancePartsPros.com is one of the... Read more

I took the cover off and the fan had separated from the bushing. Ordered a new fan and nut and it took all of 5 minutes to replace. Probably saved $159.99 service call repair and that is with a coupon. Any one can do this repair, just make sure the oven is cold as you will come in contact with metal parts. Read more

Ordered new oven control and got the best price appliance parts pros.com. It was super easy to install. Read more

It was very easy!. Just removed the screws off the trim plate and access was right there. The double oven was given to me but the handles were missing and the end caps so I just had to replace them. Read more

Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough. Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the... Read more

I removed oven panel and found the fan blades had warped and were hitting the base that fan was mounted to.I turned off the power via circuit breaker,removed fan mounting screws,removed two wires and installed new fan.Reset breaker,oven is nice and quiet now. Read more