Need Help?
Call
Package of 12
Usually ships within 4 - 14 days
Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.
M5-16 metric machine screw secures service panels and internal components in washers. Replace missing, stripped, or damaged screws during repairs.
Replace your washer door bellow to prevent leaks and restore a watertight seal. Essential when torn or showing wear to protect against water damage.
Replaced the gasket, took less than 30 minutes to get the job done. Thanks to the helpful videos you guys provide. Read more
Fix a washer that won't advance through cycles or gets stuck during wash. This timer assembly controls fill, agitate, drain, and spin sequencing.
Washer won't spin or start? This control board assembly manages cycle functions and restores normal operation. Mounts below the control panel.
I replaced the mother board which is located below the control panel. Read more
Fix a washer that won't start, pauses mid-cycle, or has unresponsive buttons. This electronic control board restores normal operation and cycle timing.
Push-in plug button for top-load washers. Snaps into trim openings to cover unused holes and restore a clean finish. Replace if cracked or missing.
This motor assembly kit includes the rotor and stator components that make up the direct-drive motor in a washing machine. The motor is responsible for spinning the wash drum during wash and spin cycles. Replace this kit if the washer is not agitating or spinning, makes loud grinding or humming noises, or if the motor has failed electrically.
Initially contacted an appliance repair man from a national, reputable company recommended by GE. He diagnosed a water pump problem over the phone. When he arrived to inspect the washer he then made the determination it wasn't the water pump. He attempted to run a spin cycle and received the same messge, load out of balance. He then, I assume through his years of experience, determined that it was a computer problem and recommended replacing the Pwb/pcb Asm-Main. He made this... Read more
Leveling pin for washer feet. Installs at the base to adjust appliance height and stability. Replace if broken, missing, or stripped threads.
5/16-18 tpt ihw s n
Replaced the Coupling Pulsator, and the Pulsator (short spindle in the center of the washer). The only problem that I encountered was how to remove the short spindle in the center of the washer...my fabric softer is in the center and you need to open that, grab the middle and loosen by turning left. Once that is out you will use a 7/16th socket and remove the entire agitator. Most of the videos show that you pull that straight up to remove - not the short one. There is still a screw to remove.... Read more
Replaces a damaged or missing M12 x 25 flange bolt in your washer. Secures panels, brackets, and internal assemblies. Needed when bolts are stripped, broken, or lost during repair.
Washer not heating or cooling properly? This thermistor temperature sensor assembly measures internal temps and sends readings to the control board.
Secures washer tub and hoses to prevent leaks and noise. Replace if worn or broken to maintain proper alignment and seal. Verify fit with your model.
I did it Read more
This funnel shower head directs water flow inside the dispenser, helping water reach the glass or icemaker chute reliably. It replaces a worn or cracked funnel to restore proper water direction and reduce splashing. What it does:
This siphon pipe connects to the washer's drain system and helps direct water out of the tub during the drain cycle. It uses a siphon action to efficiently remove wash and rinse water from the machine. Replace this part if the washer is not draining properly, water is leaking from the drain hose area, or you notice water remaining in the tub after a cycle completes.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.