General Electric Washer Parts

• Will not fill with water

The GE front loading HE washer wound paused at the rinse fill point and need manual selection of drain & spin to finish the load. Online searches told me how to get the error code. Once E22 was found online searching told me it was a water flow problem- slow fill. I removed the hoses at the washer and inspected for clogs - nothing was found. I then put the ends of the hoses in a bucket and turned on the water- strong flow. Interesting is some debris/solids came out. I’m betting over time solids... Read more

Easily replaced the knobs Read more

Replaced the hose and water inlet. Part #: AP3189243 (WH41X10077). This connects the solenoid valves to bring water into the tub. Read more

I thought initially it was a hose because it was leaking water from the bottom. On the small and medium load it didn't leak. I watched it on the large setting and noticed the water didn't shut off initially so therefore it was over filling. I ordered a switch pressure switch from Appliance Parts Pros and received it in two days. I replaced the switch, put the washer together and now it works like new. The wife is very happy to have her washer back working better than ever! Thanks! Jerry Read more

Removed fill level pressure switch knob. Removed three screws from the back of the control panel.Opened the control panel and removed electrical connector and plastic tube from the pressure switch. Removed and replaced pressure switch. Placed control panel to correct position and replaced the three screws. Read more

Found the belt was thrown off. Reinstalled the belt and when doing so felt that the pulley was wobbling on the barrel shaft. Took the pulley off and noticed the inside of the pulley was worn badly and needed to be replaced. When received the new pulley and belt easily installed and was working like new. Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

I replaced the Timer knob components. Removing the cover that contains the Timer was simpler than I anticipated. Just remove the screws on the top of the back of the machine. Hold the cover and lift up and push to the left (facing the front of the washer). Removed the Timer Knob Clip with small needle-nose pliers. Grasped the Timer and turned counterclockwise to remove and unplugged the wiring clip. The timer is seated to the cover and held securely in place with one screw. I seated the new... Read more

I looked up a YouTube video first to know how to take my washing machine apart. It was an Appliance Parts Pros Video. Very helpful! I replaced the mode shifter, water pump, washers, agitator spline, hub nut, tub bearing, tub seal and drive belt. The hub nut DID NOT want to come off. I cut it off with my Dremel and chipped out the beveled segment with a heavy duty screw driver and 3# hammer. Had to be very careful to not damage the hub assembly. I removed the Torx screws and removed the... Read more

I shopped around a bit - found one retailer that only had 1 shock in stock, another that only stocked the front shocks, etc. There is definitely a difference in the springs between the green colored and white colored shocks! I've torn this washer down before, so I'm fairly familiar with how it's put together. I've seen some of the You-tube videos on replacing this item, and some of the videos show far more disassembly than is required. I only removed the front, top, and controls, and... Read more

• Lid or door will not open
• Won't start

Went on line general information made me realise I needed to replace the door lock.Signed into appliancepartspros.com found the part and ordered it. That took about 5 minutes. A day and a half later the part arrived at my home. Repair took about 15 total minutes machine works like new again. What a pleasure to have appliance parts pros for obtaining parts at a reasonable price with prompt delivery. Read more

Replaced inlet water valve. Simple repair. Removed control panel cover with few screws on back, removed valve with 4 screws, rubber tubing and clamps, disconnected electrical spade plugs. Reversed the above and the new valve is in and works perfectly. No problems. Simple to do, and will save you $$$$. Read more

Found the belt was thrown off. Reinstalled the belt and when doing so felt that the pulley was wobbling on the barrel shaft. Took the pulley off and noticed the inside of the pulley was worn badly and needed to be replaced. When received the new pulley and belt easily installed and was working like new. Read more

• No hot or cold water
• Will not stop filling with water

Replaced inlet valve Read more

Put new hose on. It was the kind that pushed in and had a flange on it with two screws. Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

I watched your video and I replaced the water inlet valve. The problem is now fixed. It took about 5 minutes to replace. I am a 60yr old woman and it was an easy fix. Read more