General Electric Range Heating Element

Restore reliable heat on your range's small burner with this 6-inch surface coil element. Replacing a worn or burned-out coil brings back consistent temperature response and dependable everyday cooking performance.

• Supplies direct electric heat to a 6-inch cooktop burner
• Replaces a coil that is warped, cracked, or has an open/burned-out section
• Common symptoms include: burner won't heat, heats unevenly, or works intermittently
• Visible damage, hot spots, or arcing at the terminals can indicate failure

• Disconnect power by unplugging the range or switching off the circuit breaker
• Lift the old coil and pull straight out from the receptacle to remove
• Inspect the element receptacle/terminal block for discoloration or pitting; replace if damaged
• Align terminals and support, insert fully, and ensure the element sits level in the drip bowl

This bake element heats the oven cavity for standard baking operations, restoring even heat when the original element fails. It installs at the rear or bottom of the oven cavity to provide the radiant heat needed for baking. What it does:

• Heats the oven cavity to maintain proper baking temperatures.
• Replaces a burned, broken, or visibly damaged element that won't glow or heat.
• Helps correct symptoms like insufficient heat, uneven baking, or an oven that won't reach set temperature.
• Works with the oven's control system and thermostat to deliver steady radiant heat.

• Disconnect power to the appliance before starting — turn off the circuit breaker or unplug the range.
• Allow the oven and old element to fully cool before handling.
• Handle the element carefully to avoid bending or damaging the terminals or ceramic insulators.
• After installation, restore power and test the oven on a bake cycle to ensure the element heats correctly.

This oven bake element generates the heat for the Bake cycle. Replace it when the oven won't heat or takes too long to reach temperature to help restore consistent, even baking performance.

• Provides primary heat during the Bake mode
• Common symptoms of failure: no heat in Bake, very slow preheat, uneven or undercooked results
• Element shows visible damage such as blisters, breaks, or burned spots
• Replacing a failed element can restore normal oven operation

• Disconnect power at the breaker; ovens use high voltage
• Remove oven racks and access the element from the oven cavity; note screw locations and wiring
• Move wires to the new element one at a time and ensure snug terminal connections
• Avoid bending the element or overtightening screws; restore power and test Bake

This lower oven heating element supplies the heat for baking. It restores consistent oven temperatures when the original element has failed, helping your range bake evenly again.

• Heats the oven cavity during Bake mode
• Common failure signs: no heat in Bake, slow preheating, uneven baking, visible blisters or breaks on the element, or tripping the breaker when Bake is selected
• Electrical checks may show an open element when failed

• Disconnect power before servicing to avoid electrical shock
• Allow the oven to cool completely; remove racks for access
• Transfer any mounting hardware from the old element if needed; connect wires firmly to the new terminals
• Avoid flexing or touching the element surface; test operation after reassembly

This bake element heats the oven from the bottom during Bake mode. A failed element can cause no heat or slow preheat; replacing it restores reliable, even baking performance.

• Primary heat source during Bake; helps the oven preheat and maintain set temperature
• Common symptoms of failure: no heat in Bake, slow preheat, uneven baking
• Visual clues: blistering, cracking, or burn marks on the element
• If Broil works but Bake does not, the bake element is a likely cause

• Disconnect power at the breaker or unplug the range; allow the oven to cool completely
• Remove oven racks; unfasten the element's mounting screws and gently pull the element forward
• Support and disconnect the two wires; prevent them from slipping back into the oven liner
• Reconnect wires firmly, secure the element, restore power, and test Bake

By GE 6 inch, looped terminals, 1325 watt. Fits GE and HotPoint ranges where a ceramic terminal block is used. For matching 8 inch surface element order WB30X219. For ceramic terminal block order WB17X5051.

This is a surface burner unit, and it is made for ranges, stoves, and cooktops. This is a genuine replacement part made by General Electric. Surface burners, when prompted, are able to heat up so that the user can cook on top of the stove. The metal in which it is made can easily transfer the heat from the element below to the pot or pan on top. A new surface unit might be needed if the burner element will not heat. It is possible that after many years the surface burner is unable to heat up due to many uses and normal wear and tear. Be sure the appliance is completely powered down and cooled off before attempting a repair of the surface burners.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with ranges, stoves, or cooktops made by General Electric.

This bake element sits at the bottom of the oven cavity and generates the heat for Bake mode, restoring steady, reliable baking performance when the original element is worn, cracked, or burned out.

• Supplies the primary heat from the bottom of the oven during Bake
• Helps the oven preheat and maintain the set temperature
• Typical failure symptoms: no heat in Bake, slow preheating, uneven baking, or visible blisters/breaks on the element
• Visual inspection may show hot spots or damage when the element has failed

• Disconnect power at the breaker or unplug the range before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward
• Transfer the two wires to the new element terminals one at a time; secure the element to the rear wall
• Keep wires from slipping back into the insulation; restore power and test Bake mode

The Surface Element is an OEM part for GE ranges. This part provides the heat required for cooking on the cooktop. The surface element heats up when activated by the control knobs, allowing for precise temperature control to cook a variety of dishes effectively. 8" Surface Element for receptacle order WB17T10006

Common causes of a bad surface element include wear and tear from frequent use, overheating, or physical damage from cookware. 

Symptoms of a bad surface element include:

• The element not heating up or heating unevenly
• Visible damage, such as burns or cracks on the element
• The element taking longer than usual to heat up
• Intermittent heating or failure to maintain the set temperature

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This 12-inch Haliant surface element sits beneath the glass of smooth-top ranges and cooktops, providing heat for the large burner. Replacing a failed element restores reliable, even heating and full-size cooking performance.

• Generates radiant heat for the 12-inch cooking zone under the glass-ceramic top
• Works with the control to cycle power and maintain set temperatures
• Common symptoms: large burner won't heat, only part of the ring glows, or heating is weak/erratic

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift or remove the glass top to access the elements; support the top to avoid stress or cracking
• Note wire locations; move connections one at a time to the new element and secure using existing mounts
• Ensure all terminals are tight and clear of the frame before reassembly

This bake element is the lower oven heating element that produces the heat needed for bake cycles, restoring oven temperature and consistent cooking performance when the original element is damaged or not heating. What it does:

• Heats the oven cavity during bake cycles to maintain set temperatures for baking and roasting.
• Restores heating when a burned, broken or visibly damaged element causes little or no heat.
• Helps correct uneven cooking or longer-than-normal preheat times when caused by a faulty element.
• Direct-fit replacement designed to mount in the oven's lower cavity and connect to existing wiring.

• Disconnect power to the appliance at the circuit breaker before starting any work.
• Allow the oven to cool completely and remove oven racks before accessing the element.
• Replace the element mounting screws and wire terminals exactly as removed; ensure tight, secure connections.

This radiant surface element sits beneath a glass cooktop and supplies controlled heat to a single burner. Replacing a failed element restores proper heating and consistent cooking performance on the range top. What it does:

• Converts electrical power into radiant heat under the glass for one surface burner
• Works with the limiter/control to cycle and maintain set temperatures
• Typical symptoms: burner won't heat, heats intermittently, shuts off too soon, or trips the circuit when turned on
• Common diagnosis: element tests open (no continuity) with a multimeter

• 1 radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift or open the glass top per your model's service information to access the element
• Note wire locations; transfer any mounting clips/brackets as needed and reconnect wires one at a time
• Handle the element carefully and seat it correctly before reassembly; test operation before closing up

Replacement bake element for the lower oven. This is the primary heat source in Bake mode, restoring reliable preheats and even results when the original element fails. If your oven won't heat or underbakes, this part addresses the issue.

• Provides radiant heat from the bottom of the oven during Bake mode
• Common failure symptoms: no heat in Bake, won't reach set temperature, or visible breaks/blistering on the element
• Restores even baking and consistent preheat performance when replaced
• Often tests open (no continuity) when the original element is burned out

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks, then the element's mounting screws; gently pull the element forward to access wires
• Support wires so they don't retract; disconnect the two spade terminals and transfer any mounting bracket from the old element if needed
• Attach terminals to the new element, tuck wires carefully, reinstall screws, restore power, and test Bake

This 8-inch coil surface element restores consistent stovetop heating on electric ranges. Replace a warped or burned-out burner so pots heat evenly and your everyday cooking temperatures are easy to reach and maintain.

• Converts electrical power into heat for the 8-inch cooking zone
• Plugs into the surface-element receptacle for a secure power connection
• Common fix for a burner that won't heat or heats slowly/unevenly
• Replace if the coil is blistered, warped, or the terminals are burnt/pitted

• Disconnect power at the breaker or unplug the range; allow the element to cool completely
• Lift the old element slightly and pull straight from the receptacle; remove from the support
• Inspect the receptacle; replace the block if terminals are burnt or loose
• Align the new element in the drip pan/support and push terminals fully into the receptacle until seated

This broil element assembly restores the intense top heat your oven needs for broiling. Replacing a worn or failed element brings back fast, even browning and searing performance when you select Broil.

• Provides direct, radiant heat from the top of the oven during Broil
• Typical failure signs: broiler won't heat or the element won't glow red
• Can cause weak/uneven broiling or unusually long broil times
• Often shows visible damage such as breaks, blisters, or burned spots
• A shorted element may trip a breaker when Broil is turned on

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely; wear gloves and eye protection
• Note wire positions and transfer them one at a time to the new element; avoid bending the element
• Reuse existing mounting hardware; ensure terminals are fully seated and secure before restoring power

An 8-inch Haliant radiant surface element for smooth-top ranges. It replaces a worn or burned-out burner so your cooktop heats evenly and responds correctly, restoring reliable everyday cooking performance. What it does:

• Supplies controlled radiant heat beneath a glass-ceramic cooktop for the 8-inch burner position
• Common fix for a surface element that will not heat
• Helps resolve slow or uneven heating, or when only part of the ring glows
• Appropriate when the element shows visible breaks, hot spots, or burn marks

• 1 8-inch Haliant radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool completely before service
• Lift or open the glass top per your service information; handle the element carefully—it is fragile
• Move wires one at a time to matching terminals; transfer any mounting brackets/clips from the old element
• Ensure the element sits flat and centered before reassembly; test operation before cooking