Gibson Parts

The repair was a success. The switch and came looked different from the original. I called Appliance Parts Pro, they lady on the phone said that Frigidaire changed the switch and how to wire it up correctly. Problem solved. It all works as it should. Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Leaking

This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more

Easy job, I screwed the parts to the dishwasher Read more

Order the parts...!!! Read more

Order the parts...!!! Read more

• Timer will not advance

Just pulled off old knob and pushed on new one. Read more

Replace dispenser micro switch. Also replaced broken faceplate and rusty screws. Appliance parts Pro YouTube video was helpful in diagnosis and disassembly. Parts arrived quickly. Read more

Replaced the rear drum bearing assembly and the front top felt that the drum rides on and since I has it apart installed a new belt. Simple to do and takes very little time! Read more

• Shakes and moves

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

The fix took 30 seconds. The key to success was your video that explained how reinstalled parts "lock in". Read more

I easily found a replacement bin by keying in the model number of my refrigerator. Read more

Replaced springs and shocks. Read more

Changed the Frigidaire Icemaker Fill Tube Part # 241796405 (AP5671747) about a week ago and so far the Frigidaire Refrigerator seems to work fine. Did not use other ordered parts. Recently ice formed around internal evaporator fan and it started making loud noise when then fan and compressor, etc were running. A long winded history noted below if interested: I have been fighting with this Frigidaire Refrigerator for about 3 to 4 years, started out with the evaporator fan making noise when ice... Read more

My 10 year old frig door was hanging down to the point it wasnt fully closing and sealing unless you picked up on it. I ordered a lower hinge bracket, upper and lower bearing, and spacer. My bracket was bent down a little due to my kids hanging on the door when looking at the bottom shelf and i discovered my bracket was held on by only two bolts when there was supposed to be three. I ordered a bolt too. I was able to remove the bottom hinge, remove door to replace upper and lower bearing and... Read more

Took cover completely off and tried putting back, could not match up left screw with available screw hole. Tried many different configurations and sequences to make this happen. watched a video on changing the front panel, the door in it had four screws, mine 2, no help there. Searched on the hyperextending issue, found an article about dogs and kids [had both here] climbing on the door and to check the springs and linkages. Linkages intact both sides, R [opposite] side spring very stretched.... Read more

• Door won't close

My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more