Hotpoint Dishwasher Parts

The Sump Inlet is an OEM part for GE dishwashers. This part allows water to flow into the sump area, which collects and drains used wash water from the tub during the dishwashing cycle.

Causes of a bad part can range from clogs or obstructions preventing proper water flow, physical damage or cracks leading to leaks, or general wear and tear over time.

Symptoms of a bad Sump Inlet include:

• Failure of the dishwasher to fill with water
• Water leaks or puddling around the base of the dishwasher
• Excessive noise or gurgling sounds during operation

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: white. It measures about 2 inches in diameter by 2-1/2 inches deep.

This fine filter assembly sits in the bottom of the dishwasher tub and screens out small food particles so recirculating water stays cleaner. Replacing a torn or warped filter helps restore wash performance and protects the pump and spray arms from debris.

• Traps fine debris to reduce redeposit on dishes and glassware
• Supports proper water circulation and spray pressure
• Helps shield the wash pump and spray arms from clogs or damage
• Replace if the mesh is torn, warped, missing, or persistently clogged; common signs include gritty residue or food left on dishes

• Disconnect power at the breaker before servicing inside the tub
• Remove the lower rack; if required, remove the lower spray arm and release your model's retainer (nut/clip/screws) to lift out the old filter
• Clear debris from the sump; seat the new filter flat and lock/secure it fully, then reinstall any removed parts
• The filter is locked in place before running a test cycle

This timer knob replaces the cycle control knob on select dishwashers. It mounts to the timer shaft so you can choose wash cycles; a cracked or stripped knob can make the timer difficult to turn or impossible to set.

• Mounts on the timer shaft to set and advance dishwasher cycles
• Replaces a broken, cracked, stripped, loose, or missing knob
• Helps when the timer won't turn by hand or the knob slips on the shaft
• Restores normal feel and alignment of the front-panel control

• Disconnect electrical power at the breaker before servicing.
• Pull the old knob straight off the timer shaft; do not pry on the console.
• Align the new knob with the shaft and press firmly until fully seated.
• Restore power and verify smooth rotation through all settings.

This line cord supplies electrical power from the wall outlet to the appliance. Replacing a worn, cut, or heat-damaged cord restores safe, reliable power and can help resolve no-power or intermittent operation issues.

• Delivers AC power from the outlet to the unit's electrical system
• Helps correct no-power or intermittent power when the cord is moved
• Ideal replacement for cords with cuts, fraying, or burn/discoloration on the plug
• Supports proper grounding and safe operation when installed correctly

• Disconnect power before servicing; ensure the appliance is fully de-energized
• Match wire routing and connections to the product's wiring diagram; ensure a secure ground
• Use an appropriate strain relief if required by the product to prevent abrasion
• Route the cord away from sharp edges, moving parts, and hot surfaces

Lower dishwasher rack roller axle only. Color: White. Measures about 1 inch wide by 1 inch high by a 1/2 inch deep. For Gray color order part number WD35X21041.

This dishwasher sump inlet forms the sealed passage between the tub and the pump system, directing wash water out of the basin. Replacing a cracked or clogged inlet helps stop leaks and restores steady water circulation and cleaning performance.

• Channels water from the tub into the circulation/drain system
• Maintains a watertight seal at the tub floor to prevent leaks and air intrusion
• Helps preserve spray pressure and consistent wash performance
• Common symptoms of failure: water leaking under the unit, weak cleaning results, unusual pump noise, visible cracks or warping

• Disconnect power and water supply; wear cut-resistant gloves and place a towel or shallow pan to catch residual water
• Access may require removing the lower spray arm, filters, and toe panel; note hose/clamp orientation before removal
• Clean sealing surfaces before seating the new inlet; secure per model design and ensure all connections are tight
• Reassemble and run a short test cycle while inspecting for leaks

This is a hose chamber, or dishwasher hose pump. This part attaches to the back of the dishwasher and is the direct line for the water to get in and out during the washing cycle. This specific part prevents leaking and is very important to the machine. The user might need to replace this part if the dishwasher is leaking, if the machine is not putting in or draining water properly, or if the machine has stopped working altogether. Anyone can complete this repair with basic household tools such as a screwdriver, pliers, and working gloves. Always make sure the machine is empty of dishes and is drained of water before starting the repair. Also make sure it is unplugged from the electrical source and is turned off completely. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from manufacturers like General Electric, Hotpoint, RCA, and more.

This leveling screw adjusts your dishwasher's leveling leg so you can set the cabinet height and get the unit perfectly level. Proper leveling helps the door seal correctly, reduces rocking, and cuts excess vibration and noise.

• Threads into the leveling leg to raise or lower the dishwasher for accurate leveling and stability
• Helps prevent rocking or wobbling and supports proper door alignment and sealing
• Can reduce vibration/noise associated with an out-of-level installation
• Replaces a stripped, bent, or missing adjustment screw to restore adjustability

• Disconnect power and turn off the water supply; protect flooring before adjusting or replacing
• Remove the toe-kick/access panel to reach the adjuster; support the dishwasher's weight before turning the screw
• Start threads by hand to avoid cross-threading; do not overtighten
• After adjustment, verify level side-to-side and front-to-back with a level and recheck door operation

Includes screws.

This inlet sump is the lower-tub water intake for the circulation system. It channels wash water to the pump and seals the connection, helping prevent leaks and restoring proper wash performance when the original is cracked, warped, or clogged.

• Directs wash water from the tub into the circulation pump
• Maintains a watertight seal at the pump/sump opening
• Common failure symptoms: water leaking from beneath the unit, poor cleaning results, unusual noise from the pump area
• Visual clues: cracks, deformation, or mineral buildup on the sump inlet

• Disconnect power and shut off the water supply before servicing
• Access is typically from inside the tub and/or the bottom; remove lower rack, spray arm, and sump cover as needed
• Transfer existing clamps/seals and inspect gaskets; replace any worn seals for a proper fit
• Seat the sump fully, secure connections, then run a short cycle to check for leaks

Color: Black

This float stem is the vertical rod that links the dishwasher's tub float to the float switch. It ensures the fill valve shuts off at the correct level to help prevent overfilling, leaks, and poor cleaning results.

• Transfers the float's up/down movement to the float switch to stop water intake
• Helps maintain proper water level and protect against overfill-related leaks
• Failure may cause continuous filling/overfilling, low water level/poor cleaning, or a float that binds or feels loose
• Replace if the stem is cracked, warped, or missing

• Disconnect power and shut off water before servicing
• Remove the lower rack, take off the float cap, and lift out the float to access the stem
• From below the tub, detach the stem from the switch/retainer and install the new stem in the same orientation
• Ensure the float moves freely and actuates the switch; run a fill test and check for leaks
• Steps can vary by model.

Color: White

This is a replacement upper tower rack. This is a genuine OEM part made by General Electric and has been sourced directly from the manufacturer. This part is intended to replace a defective, cracked, or broken upper tower rack on various models of dishwasher. The upper tower rack fits onto the upper rack of the dishwasher and helps to ensure that the upper spray arm functions properly and that dishes come out clean. Over time and with regular use, the upper tower rack may become cracked or damaged and will require replacement. For safety purposes, always ensure the dishwasher is completely unplugged from power and water before attempting this repair. Be sure to follow appropriate safety precautions when attempting to repair any appliances. For more accurate information on how and where to install this upper tower rack the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this upper tower rack is suitable for use on several different models of dishwasher manufactured by General Electric, Hotpoint, and other GE brands. This is a genuine part made of high-quality, durable plastic and is sold as an individual part.

The Funnel Service Kit is an OEM replacement part for GE dishwashers. It includes a water inlet funnel and seals necessary for proper water flow within your dishwasher. This part helps prevent leaks and ensures that water is properly directed into the dishwasher.

Symptoms of a faulty water inlet funnel service kit include:

• Water leaks from the dishwasher
• Insufficient water flow during the wash cycle
• Inconsistent cleaning or rinsing performance

Causes of a bad water inlet funnel service kit can include wear and tear over time, blockage from debris or mineral buildup, or damage to the funnel or associated components. If you notice issues such as water leaks, inadequate water flow, or inconsistent cleaning results, it may be time to replace the old or damaged water inlet funnel service kit with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.