Hotpoint Dishwasher Parts
Genuine Ge part
By: Ge
Part Number: WD24X10045
Replacement drain hose kit for dishwashers. Flexible tubing routes wastewater from the wash chamber to the pump outlet. Replace if cracked or leaking.
Do-It-Yourself Stories from Customers like You
$1000 dishwasher didn't clean dishes Kevin W. • Rochester , MA • January 20, 2016
Our GE was installed about 8 years ago and was AWESOME for much of its early life. However, progressively its cleaning ability diminished. By replacing all the spray arms (clogged with debris), filters, drain hose, and sump...this dishwasher cleans like it did when it was new! Cost was around $100 (also replaced a wheel and the silverware basket) and labor was relatively simple. And to think...my mother-in-law said, "Wouldn't it just be easier to buy a new one?!?".
Read more
More
$36.49
- Compare At:
-
$43.06
- You Save:
-
$6.57
Genuine Ge part
By: Ge
Part Number: WD22X154
Lower spray arm assembly for dishwashers. Rotates to distribute water throughout the tub. Replace if tabs are broken, arm is cracked, or threads are stripped.
Do-It-Yourself Stories from Customers like You
The old ge dishwasher spray arm tabs had broken off Peter H. • Hinesburg , VT • June 29, 2014
The replacement arm arrived promptly. Removing the old spray arm hub was very difficult by hand, plumbers wrench, or adjustable wrench. However, by inserting a screwdriver trough the two opposite holes where the tabs had broken off, it is relatively easy to unscrew the old hub.
Read more
More
$45.95
- Compare At:
-
$55.14
- You Save:
-
$9.19
Genuine Ge part
By: Ge
Part Number: WD7X14
The Dishwasher Door Cable is an OEM replacement part for GE dishwashers. It works with the door latch assembly to ensure secure closure of the dishwasher door. The cable is responsible for connecting the door handle mechanism to the latch, allowing users to easily open and close the door with a gentle pull or push. Note: It is recommended to replace both at the same time.
Symptoms of a bad door cable include:
- The door not fully latching or staying closed securely
- Excessive movement or play of the door when closed
- The cable becoming worn, frayed, or detached
Causes of a bad cable can be frequent use that results in wear and fatigue of the internal wiring over time. Damage from harsh detergents or excess moisture can also compromise the cable.
This OEM GE replacement part is compatible with models from Hotpoint, RCA, and some Kenmore dishwashers as well.
Do-It-Yourself Stories from Customers like You
Soap dispenser wouldn't close door kept falling down Graeme M. • Branford , CT • October 07, 2017
First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then...
Read more
More
$26.95
- Compare At:
-
$32.34
- You Save:
-
$5.39
Genuine Ge part
By: Ge
Part Number: WD12X10408
The Filter Ball is an OEM replacement part for GE dishwashers. As a key internal filtration component, it helps trap and remove food soils and other residue from washing water to maintain hygienic cleanliness standards.
Causes of a bad filter ball can include worn filter mesh that no longer adequately strains soils or substances that pass through more readily over time.
Symptoms of a bad filter ball include:
- Dirty wash water that fails to fully sanitize dishes
- Cloudy rinse water that leaves behind streaks and residue
- Excess food debris collecting in drainage areas
This GE replacement filter ball is also compatible with some Hotpoint, RCA, and Kenmore dishwashers.
Do-It-Yourself Stories from Customers like You
Dishwasher was not draining good Stan C. • Aberdeen , WA • January 18, 2017
Replaced sump and related pieces. Also replaced door baffles that were getting bad. The hardest part of job was removing the dishwasher from the its spot in cabinets. The info on site made replacing parts easy.
Read more
More
$18.73
- Compare At:
-
$22.29
- You Save:
-
$3.56
Genuine Ge part
By: Ge
Part Number: WD19X10038
Fix dishwasher leaking from pump housing with this impeller & seal kit. Repairs worn seals causing water leaks. DIY-friendly, typically 30 minutes.
Do-It-Yourself Stories from Customers like You
Dishwasher not draining William C. • Yazoo City , MS • January 11, 2018
Replaced pump impeller.
Read more
More
$52.95
- Compare At:
-
$63.54
- You Save:
-
$10.59
Genuine Ge part
By: Ge
Part Number: WD01X10175
The Check Valve Flapper is an OEM replacement part for GE dishwashers. It is a small but crucial component located within the water inlet valve assembly. The check valve flapper regulates water flow into the dishwasher, allowing water to enter during the fill cycles but preventing backflow when the water is drained.
Causes of a bad check valve flapper can include wear and tear over time, mineral buildup that causes sticking, or damage to the flapper itself. This prevents the flapper from opening and closing as intended.
Symptoms of a bad check valve flapper include:
- Slow or incomplete filling of water
- Dripping or leaking water from the inlet area
- Error codes related to water issues
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.
Do-It-Yourself Stories from Customers like You
Continuously plugged spray arms from disintegrated rubber sump Bruce B. • Tega Cay , SC • December 27, 2014
Pulled dishwasher from the cabinet and flipped onto its side. Easy access to sump and drain flapper valve that I also replaced. Rubber sump coming apart into soft pills & chunks and plugging spray arms. Better now but it's rediculous that GE would make components that dissolve this way.
Read more
More
$13.99
- Compare At:
-
$16.74
- You Save:
-
$2.75
Genuine Ge part
By: Ge
Part Number: WD03X20445
Counterbalances your dishwasher door for smooth opening and prevents sudden dropping or slamming. Replace if fatigued, broken, or missing.
Do-It-Yourself Stories from Customers like You
GE door came off hinges and was not staying closed Donnell W. • Ferguson , MO • October 12, 2019
Once I located the parts involved in the factory exploded drawing I ordered a cable and spring. Then, when I had the dishwasher pulled out I saw that both cables had simply slipped off of their pulleys and that the door needed to be re-set properly into its drop-down metal studs.
So now I have a spare set for any problems in the future! Very easy - two screws under the counter and pull forward. Shipping was quick and easy. First time customer.
Read more
More
$12.79
- Compare At:
-
$14.07
- You Save:
-
$1.28
Genuine Ge part
By: Ge
Part Number: WD26X10025
Dishwasher not draining or water pooling at bottom? This drain pump assembly removes water during the drain cycle. DIY repair in about 45 minutes.
Do-It-Yourself Stories from Customers like You
Water would not drain Paula M. • Crestview Hills , KY • November 14, 2014
Replaced the pump drain assembly
Read more
More
$90.95
- Compare At:
-
$108.23
- You Save:
-
$17.28
Genuine Ge part
By: Ge
Part Number: WD15X28379
Fixes dishwasher not filling with water or leaking inside the tub. Controls water flow during wash cycles. Straightforward DIY repair with basic tools.
Do-It-Yourself Stories from Customers like You
Defective dishwasher water intake pump. Jim J. • Lorraine , KS • July 10, 2020
Only two screws hold the mount of the pump in the lower left near the floor. Easy access by removing the front covers then remove the two mounting screws to the pump assy. Then remove the intake and output hoses. I noticed on the new pump a male hose bib on the intake. Supplied with the dishwasher was the smooth intake water tube. Best to not reuse this supplied hose. It just won't clamp tight enough for a good seal. Cut a portion from a garden hose the same size as the intake valve bib...
Read more
More
$29.44
- Compare At:
-
$35.33
- You Save:
-
$5.89
Genuine Ge part
By: Ge
Part Number: WD22X25465
Coarse filter screen traps food debris and soil in your dishwasher's sump. Replace when clogged or cracked to maintain wash performance. Verify fit.
Do-It-Yourself Stories from Customers like You
H2o Jan K. • Victor , NY • March 07, 2026
Changed the water pressure sensor
Read more
More
$11.59
- Compare At:
-
$13.91
- You Save:
-
$2.32
Genuine Ge part
By: Ge
Part Number: WD03X10026
Replacement spring for dishwasher door latch mechanism. Provides tension to keep plunger engaged. Replace if broken, lost, or stretched during repair.
Do-It-Yourself Stories from Customers like You
Interlock switch was broken Gregory L. • Cape Coral , FL • June 06, 2015
First off OUTSTANDING experience with AppliancePartsPros.com! Ordered my parts on Tuesday and they arrived Wed morning!! Replaced interlock switch plunger and spring, which was obviously broken compared to the new one. This solved the problem of my door not latching but the machine would still not turn on.
So with two interlock switches on the door, one had to be bad. So decided to start by replacing one switch at a time until I found the bad one. If both were bad I would just buy a...
Read more
More
$11.94
- Compare At:
-
$13.82
- You Save:
-
$1.88
Genuine Ge part
By: Ge
Part Number: WD01X10342
This is a genuine replacement coupler for select dishwashers made by GE and Hotpoint. The dishwasher coupler is designed to connect the spray arm to the unit and provide the connection for the water supply. This durable plastic coupler is subject to high heat and repetitive motion and can break or wear down over time. This could result in dishes not be cleaned properly. The unit may also be leaking or failing to drain. In the event that this happens, a replacement will be needed. This OEM coupler is manufactured to exact standards. It is sold as an individual unit and does not include any additional accessories or hardware. The spray arm will need to be accessed in order to complete this repair, which requires a nut driver and flathead screwdriver. Be sure to wear gloves and unplug the unit before performing any repairs. Remove the spray arm and the filter in order to access the coupler. Remove the old part and replace the new one, then replace the filter and spray arm and test the unit for leaks.
Do-It-Yourself Stories from Customers like You
Dishwasher was not draining good Stan C. • Aberdeen , WA • January 18, 2017
Replaced sump and related pieces. Also replaced door baffles that were getting bad. The hardest part of job was removing the dishwasher from the its spot in cabinets. The info on site made replacing parts easy.
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Ge part
By: Ge
Part Number: WD18X214
Fix dishwasher leaks from cracks or tears in the pump connector. Requires removing dishwasher and pump access. Video guide available for DIY repair.
Do-It-Yourself Stories from Customers like You
Broken base spray arm tab that holds the bottom rotating spray arm in place Barry G. • Sinking Spring , PA • August 24, 2015
In the How to fix it your self section of Questions and Answers, your answers for removing the Base Spray Arm is incorrect. It states "just stick a screw driver into the base spray arm from inside the tub and turn", that does not work. Their are 2 tabs that in gauge the base spray arm with the tub. A 4 prong round wrench is required to insert from the bottom into the pump connector and turn the nut that sits inside.
Read more
More
$28.95
- Compare At:
-
$34.16
- You Save:
-
$5.21
Genuine Ge part
By: Ge
Part Number: WD22X20688
The Hub is an OEM replacement part for GE dishwashers. It is the central mechanism which attaches to the tub and facilitates rotation of the upper spray arm above dishes.
Causes of a bad hub include wear from years of repeated rotation, accumulation of hard water scale deposits inside moving parts, or accidental impact damage. This reduces proper function over time.
Symptoms of a bad hub include:
- Loud clunking or grinding noises from the center mechanism
- Reduced cleaning performance on upper racks or portions of dishes
- Dishes showing water spots or soil in sections not adequately rinsed
- Inability to attach or move the upper spray arm assembly smoothly
This OEM GE hub replacement is also compatible with Crosley, and KitchenAid models.
More
$11.70
- Compare At:
-
$12.92
- You Save:
-
$1.22
Genuine Ge part
By: Ge
Part Number: WD05X26780
Dishes not drying or wet after cycle? The heating element heats air during drying. Simple DIY repair with video guide, typically under 30 minutes.
Do-It-Yourself Stories from Customers like You
Dishwasher won't heat to dry the dishes Michael F. • Eudora , KS • December 07, 2019
Replaced heating element.
Read more
More
$35.95
- Compare At:
-
$43.14
- You Save:
-
$7.19
Genuine Ge part
By: Ge
Part Number: WD24X10014
Replaces cracked, kinked, or chewed drain hose that carries wastewater from your dishwasher to household plumbing. Essential for proper drainage function.
Do-It-Yourself Stories from Customers like You
The dishwasher would not drain sometimes Thomas W. • Oceanside , CA • October 02, 2016
I replaced the pump drain assembly. The flapper valve was included in the assembly, so I did not need to order that. On previous repairs, the old drain hose was tricky to reinstall, so I replaced it and the hose clamp.The silverware basket had holes in the bottom and required replacement. I had some broken tine clips.
Read more
More
$38.39
- Compare At:
-
$45.68
- You Save:
-
$7.29
Popular Hot Point Dishwasher Models