Jenn-Air Control Board

Fixes refrigerator not cooling or freezing caused by failed compressor inverter. Restores variable-speed compressor operation and consistent temperatures.

Fix a refrigerator that won't cool or has compressor start failures with this compressor control board. Restores reliable compressor operation.

This electronic oven control replaces the console control used to operate a single-convection oven, restoring user inputs and cycle selection so you can reliably set temperature, timers and cooking modes. Ideal when display, touchpad or convection functions fail. What it does:

• Replaces the oven's main user control to allow selection of bake, broil, convection and timed functions
• Restores touchpad/button input and on-screen feedback when controls are unresponsive or blank
• Helps resolve symptoms such as no display, unresponsive buttons, or inability to start bake/convect cycles
• Interfaces with oven components to relay temperature and command signals to the heating system

• One control (single-conv) as shown

• Disconnect power at the circuit breaker before starting any work to avoid shock hazard
• Handle the control assembly carefully; avoid touching circuit board components and use anti-static precautions if available
• Installation typically requires removing the oven console or back access panel and unplugging the old control connector—refer to OEM service instructions

Fix excessive frost buildup in your freezer with this defrost timer. Restores the 6-hour defrost cycle to keep cooling consistent. Moderate DIY repair.

Fix an oven with no display, unresponsive buttons, or temperature control issues. This electronic control board restores user input and cycle selection.

This fountain switch controls the refrigerator dispenser's user-activated circuit so the dispenser responds when the lever or pad is pressed. Replaces a worn or failed dispenser switch to restore normal dispenser control. What it does:

• Acts as the user-activated switch for the water/ice dispenser circuit
• Allows the dispenser to energize the valve or auger motor when pressed
• Commonly replaced when dispenser fails to respond or is intermittent
• Helps stop unexpected dispenser activation due to a stuck switch

• One fountain switch

• Disconnect power to the appliance before beginning any repair
• Access may require removing the dispenser/control panel; handle plastic trim carefully
• Avoid pulling on wires; disconnect connectors by their housings, not the wires

This refrigerator ice level control board monitors ice production and storage levels in your automatic ice maker. It signals when to stop making ice when the bin is full and resume production when ice is needed. Replace this control board when your ice maker overproduces ice, fails to stop when full, or doesn't restart ice production when the bin empties.

Control panel buttons not responding or stuck? This range keypad assembly restores touch-sensitive controls. Direct replacement for worn touchpads.

Ice maker stopped working or not producing ice? This control board monitors ice levels and regulates production. DIY-friendly repair, most installs in 10-20 minutes.

Refrigerator won't restart after power outage or showing PF error? This power control board regulates compressor and cooling fans. DIY install in 50 minutes.

Fix an oven that won't heat, shuts down during cooking, or has a blank display. This control board manages temperature regulation and oven functions.

This electronic control board with overlay manages your range or wall oven's heating and user interface. Replacing a failing control restores accurate temperature regulation, proper bake/broil operation, and a readable display so the appliance responds as it should.

• Regulates oven heat by switching bake/broil circuits based on temperature sensor feedback
• Powers and displays the clock, timer, and status messages
• Interprets keypad/touchpad inputs to run bake, broil, and clean cycles
• Common failure symptoms: dark or flickering display, unresponsive buttons, oven won't start or maintain set temperature, or error codes

• Disconnect power at the breaker before servicing; verify no voltage present
• Use ESD precautions and handle the board by its edges
• Photograph/label wiring; move connectors one at a time to the new board and seat fully
• After installation, run any model-specific checks or calibrations per the service/tech sheet

Dishwasher won't heat, cycle, or start? A failed control board disrupts heating, wash cycles, and dispenser timing. Moderately challenging DIY repair.

Fixes refrigerator displays flashing, unit cycling on/off, or fans not running. This power supply board converts AC to DC for controls and components.

This electronic control board regulates the appliance's console functions so cycles, settings and displays operate correctly. Replaces a faulty console module to restore responsive controls and normal cycle selection. What it does:

• Manages user inputs, cycle selection and timing signals for the appliance
• Controls display indicators, LEDs and electronic user-interface feedback
• Communicates with other modules to start/stop cycles and control features
• A failed board can cause unresponsive buttons, incorrect displays, or cycles that won't start

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available
• Verify the part number and appliance model match before installation

Fix an unresponsive keypad, blank display, or missing timer functions. This oven clock control board restores timed-cook features. Moderate DIY repair.