Jenn-Air Fuse Or Sensor

This inline fuse is a replaceable safety device that protects your appliance's wiring and components from overcurrent. It restores circuit protection so the appliance can operate safely after a blown fuse is replaced. What it does:

• Protects the wiring harness and electrical components by interrupting power if a short or overload occurs
• Commonly used where a single-point fuse is needed inline with a circuit
• Resolves symptoms like a non-starting unit, intermittent power loss, or a tripped circuit when caused by a blown fuse
• Works as part of the appliance's electrical protection system when installed in the proper harness location

• Disconnect power to the appliance before inspecting or replacing the fuse
• Visually check the blown fuse or use a multimeter before replacing
• Install only in the correct harness location and ensure secure wire connections
• If the replacement fuse blows immediately, stop and diagnose the underlying short or fault

The Thermal Fuse is an OEM component specifically designed for Whirlpool ovens. As an important safety device, it is located near heat-producing elements inside the oven cavity. 

Causes of a bad thermal fuse include overheating of elements or surrounding components over time, which can eventually blow the fuse. 

Symptoms of a faulty thermal fuse include:

• The oven failing to heat or operate heating cycles fully
• Heating elements abruptly shutting off during baking  
• An unusual burning smell emanating from the oven

This genuine OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore oven models as well.

A high limit thermostat that stops heat when a dryer's temperature gets too hot, helping protect the heating system and cabinet from overheating. It's a direct-replacement thermostat used in many gas and electric dryer heater assemblies. What it does:

• Opens the heating circuit if temperatures exceed safe limits to prevent overheating.
• Helps protect the heating element, housing, and internal components from heat damage.
• A failed thermostat can cause no heat or intermittent heating in the dryer.
• Works with the dryer's safety controls to maintain normal operating temperature.

• Disconnect power (and gas if applicable) before servicing; allow unit to cool completely.
• Located on or near the heater box or blower housing; follow your model's service manual for access.
• Replace with the exact part number to maintain original safety settings.

This 20-amp circuit breaker restores overcurrent protection to the appliance's electrical circuit, helping prevent damage from short circuits or overloads. It replaces a worn or tripped breaker so the appliance can receive proper power. What it does:

• Acts as an overcurrent safety device that trips when current exceeds safe limits
• Protects wiring and components from damage caused by overloads or short circuits
• Common symptom: appliance won't power on or stops powering intermittently
• Common symptom: breaker repeatedly trips during normal operation

• Disconnect power at the house breaker before inspecting or replacing the part
• Handle terminals carefully; ensure connectors are fully seated and tight
• Replace with the exact part number for fit and proper electrical rating

A hi-limit safety switch that stops heating when temperatures get too high, protecting the appliance from overheating and helping prevent damage. Designed to replace a failed thermal cutoff to restore safe temperature control. What it does:

• Opens the heating circuit when internal temperature exceeds the safe limit to prevent overheating
• Commonly replaces a failed or intermittently opening thermal limit control
• Helps stop burners or heating elements from running unchecked when a thermostat fails
• Addresses symptoms like no heat, intermittent heating, or safety trip shutdowns

• Disconnect power before accessing heating components and wiring
• Verify the part matches the appliance diagram and wiring orientation before installation
• If corrosion or other damage is present on connectors or terminals, replace or repair per OEM guidance

This 15 amp, 250 volt replacement fuse protects your appliance's electrical circuits by interrupting power when a fault or overload occurs. It restores safe operation once the underlying issue is fixed and the fuse is replaced. What it does:

• Acts as an overcurrent protection device for circuits rated up to 15 A and 250 V
• Prevents damage to wiring and components by opening the circuit during an overload or short
• Common symptom: appliance has no power or specific functions stop working after a sudden failure
• Replacing a blown fuse can resolve intermittent power loss or complete power failure tied to a single blown element

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only with a fuse of the same amperage and voltage rating to maintain safety and proper protection
• Use insulated tools and avoid touching live terminals; internal access may require disassembly, follow OEM service instructions
• If fuses blow repeatedly, stop using the appliance.

This thermistor is a refrigerator temperature sensor that monitors internal air temperature so the control board can regulate cooling. Replaces a failed sensor to help restore accurate temperature readings and more consistent cooling. What it does:

• Senses internal refrigerator temperature and sends a variable resistance signal to the control board
• Helps the control system cycle the compressor and fans correctly for stable temperatures
• Commonly replaced when refrigerator runs too cold, too warm, or has irregular cooling cycles
• Can address temperature-error codes or defrost control issues when the sensor is faulty

• Disconnect power to the appliance before inspecting or replacing the sensor
• Handle the sensor and wiring harness carefully to avoid damage to the probe or connectors
• Install in the original sensor mounting location and secure wiring away from moving parts

This oven temperature sensor monitors the oven cavity temperature and sends readings to the control board so your range can maintain accurate cooking temperatures. Replacing a faulty sensor restores proper temperature sensing for reliable bake and roast results. What it does:

• Measures internal oven temperature and reports it to the control board
• Helps maintain set cooking temperatures for even baking and roasting
• Common repair for ovens that run too hot, too cool, or display temperature errors
• Works with electronic controls to enable accurate temperature cycles

• One temperature sensor

• Disconnect power to the appliance before beginning any repair
• Sensor typically mounts inside the oven cavity and connects to a plug or harness; confirm connector location before removing
• Handle sensor carefully to avoid bending or damaging the probe

This cycle thermostat regulates temperature during appliance heating cycles to help maintain safe, consistent operation and proper cycle performance. It replaces a worn or failed thermostat to restore correct temperature control. What it does:

• Senses and opens/closes at set temperatures to control heating during cycles
• Prevents continuous heating when the thermostat reaches its limit
• Can cause no-heat, overheating, or short cycling when faulty
• Works with the appliance's control system to maintain cycle timing and safety

• Disconnect power to the appliance before inspecting or replacing the thermostat
• Handle thermostat and terminals carefully; avoid bending sensing elements

This high-limit thermostat is a temperature safety switch that helps prevent overheating by opening the circuit when temperatures exceed safe limits. It restores normal operation once the temperature cools, protecting the appliance and reducing fire risk. What it does:

• Monitors internal temperature and opens the circuit if heat gets too high
• Prevents overheating that can cause damage or burn odors
• Commonly replaces a failed or intermittently tripping thermal safety switch
• Works as part of the appliance's temperature-safety system, not a primary temperature control

• Disconnect power to the appliance before attempting replacement
• Observe proper wiring orientation and secure terminal connections
• Replace only with the exact part specified for your appliance

This high-limit thermal fuse cuts power when temperatures exceed safe levels to protect heating circuits and prevent fires. Replace a failed fuse to restore proper thermal protection and help your appliance heat and run correctly. What it does:

• Opens the circuit if the heater area overheats to protect the appliance from thermal damage
• May resolve no-heat or intermittent-heat symptoms in dryers and other heated appliances
• Can stop an appliance from running if the thermal cutoff is blown
• Acts as a one-time safety device that must be replaced if it has opened

• Disconnect all power before accessing or replacing the part
• Verify the failed fuse with a continuity test; a blown fuse will show no continuity
• Replace with the exact part number to ensure correct temperature rating and fit
• If the thermal fuse has blown, inspect and repair the underlying cause (venting, air flow, or heating element) before return to service

This fixed thermostat senses temperature and opens or closes the electrical circuit to control heating. It replaces a failed temperature-sensing switch to restore proper heating control and safety. What it does:

• Monitors appliance temperature and interrupts power when the set limit is reached
• Prevents overheating by opening the circuit at high temperatures
• Restores normal heating control when a failed thermostat causes no heat or continuous heating
• Works as a safety/limit device in the appliance's heating system

• Disconnect power to the appliance before starting any repair
• Handle the thermostat and sensing element gently; avoid bending or stressing terminals
• Refer to the appliance service manual or OEM instructions for proper placement and mounting

This high-limit thermostat (hi-limit switch) is a temperature safety device that stops the heating circuit if the appliance overheats, helping protect the unit and restore proper heat control when replaced. What it does:

• Opens the heating circuit if internal temperature exceeds safe limits to prevent overheating.
• Controls whether the heater/element receives power based on temperature.
• When faulty, common symptoms include no heat or intermittent heating and repeated thermal cutouts.
• Can be tested for continuity to confirm electrical function.

• One high-limit thermostat (hi-limit switch).

• Disconnect power before inspecting or replacing; risk of shock or injury if energized.
• Note and label wire locations or take a photo before removal for correct reassembly.
• Verify part compatibility with your model before installing; confirm continuity after installation.