Jenn-Air Range Parts

We recently purchased a house with Jenn-Air appliances. The previous owner had used something to clean the knobs on the stove that removed the imprint. Ordering these was easy, they fit with no problem and are manufacture initial product quality. Very Pleased. The only suggestion I would have is to provide instructions on how to install the oven door gasket. I have not attempted that yet but will soon. Read more

• Element will not heat

I ordered 2 bake elements and bulbs and was able to easily fix 1 of the ovens. The serviceman who repaired the left oven did not repair it correctly so, one of the wires was not accessible so, I could only fix one oven. After shutting off the power, I EASILY fixed the right oven - with a LOT of care and a little elbow grease - in disconnecting the broken element, by doing exactly as it said to in the video, making certain not to allow the wires to slip back into the hole that it was pulled... Read more

Installed it according to video watched. Read more

• Element will not heat
• Little to no heat when baking
• Oven not heating evenly

Removed 2 sheet metal screw pulled element out about 2 inches. Removed two Spade connections. Removed the element from the oven. Inserted the new element into the over, connected the two spade connector. Reinstalled the two sheet metal screws. Set the oven to bake for testing and tested until the element turned red. Total time less than 5 minutes. Read more

I was just replacing my filter,on my vent. Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

Purchased proper hinges. Lifted oven doors off the hinges. Removed screws securing the oven to the cabinet, then slid out the unit from the cabinet far enough to access the hinges. Then removed trim to better access the hinges. Then removed the screws holding the hinges. Then installed the new hinges, secured them with the screws, then reinstalled the trim, then slid the unit back into the cabinet, and secured it in place with the screws. Finally, I placed the oven doors back on my hinges. ... Read more

It was a simple process to enter the model number of our glass cook top stove; learn the part number required and order. It arrived in 2-days -- least expensive shipping method. The cooktop was removed with a Phillips-head screwdriver by 4 small sheet metal screws on the right and left side of the oven. The oven's power to the cooktop was easily disconnected via two "clips" and one ground. Would have cost way more with an appliance repair shop and it's an easy do-it-yourself repair. Read more

My new cooktop cartridge for my Jen-Air cook range works great. The range is probably around 40 years old. The old two-burner cartridge just plain wore out! Both burners cook evenly on all heat selections. Price of less than $200.00 was very reasonable. Thanks again for your help! Very easily plugs in to the range. Read more

Replaced numerous items including this Inverter and two control boards but the Magnetron was the ultimate solution. The tip was clearly burned through when I removed the original. Read more

The instructions that came with the replacement smaller surface heating element provided no help about how to open the top of the range, so I checked the internet. I found several videos on replacement of surface elements in flat top ranges, but none for our particular range, so I Google-searched a simple question, “How to open the top of a 6898VVD Magic Chef range”. The AI Overview answer had several points, most of them not useful, except for the last one: “Hidden Clips: There might be... Read more

Only the lower element was burned out, but I opted to replace both. Ordered from AppliancePartsPros and received them very quickly! A few screws, unplug and plug in the new elements, replaced the screws, and DONE! This has to be one of the easiest repairs a homeowner can do. Thanks, AppliancePartsPros for carrying the original equipment parts and providing the fast shipping! Read more

So I ordered the burner and Ithe switch because I wasn't sure what part was defective. I pulled the oven out and I removed the 6 1/4 inch screws on each side of the glass top as well as the 2 Phillips head screws on the back, removing the 2 1/4 screws on the shield on the back gIves you easier access to them, then lifted the glass top up on the front to access the switch and burners. Make sure you turn the power off before beginning this process. When lifted up the wires connected to the... Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

• Won't start

First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more