Jenn-Air Parts

This relay change kit replaces the failed relay assembly that controls motor or compressor power, restoring proper electrical switching for normal operation. Use this kit to replace a worn or intermittently working relay with an exact-fit factory component. What it does

• Switches power to the motor/compressor when the appliance calls for it
• Restores reliable start and run signals when a relay has failed or sticks
• Addresses symptoms like clicking on start, no motor/compressor operation, or intermittent runs
• Helps prevent damage from repeated failed start attempts

• One relay change kit

• Disconnect power before servicing to avoid shock or damage
• Replace only with the exact OEM relay kit for safe, reliable operation
• Verify wiring and connectors are secure and undamaged before restoring power

Replacement burner switch that controls the heat level for an electric range surface element, restoring proper temperature selection and burner responsiveness. Use this switch when a burner is unresponsive, stuck at one setting, or heats erratically. What it does:

• Regulates power to a surface element so you can select low-to-high heat settings.
• Replaces a failed surface control switch that prevents burners from changing temperature.
• Common symptoms it can fix: burner won't heat, stuck on one setting, no click/response, or inconsistent heat.
• Works as the control interface between the knob and the element on compatible electric ranges.

• Disconnect power at the breaker or unplug the range before starting any repair.
• Photograph or label wires before removal and match terminals exactly when installing the replacement.
• Use insulated tools and avoid contact with live terminals; restore power only after reassembly.

This ignition switch controls spark to a gas range burner so burners light reliably when a knob is turned. Replaces a worn or failed switch to restore normal ignition and consistent burner operation. What it does:

• Sends the electrical spark signal to the burner igniter when the control knob is turned
• Allows the range to ignite burners; a failed switch can prevent sparks and burner ignition
• Works with the range's safety/ignition system to enable proper start-up sequencing
• Helps eliminate intermittent sparking or no-spark symptoms linked to a faulty switch

• Disconnect power and turn off the gas supply before beginning service
• Basic hand tools required; access may require removing the cooktop or control panel
• Handle electrical connections carefully and restore grounding; follow manufacturer instructions

This switch harness assembly connects the control panel switches to the appliance's main wiring, restoring reliable electrical connections for panel buttons and cycle selection. It replaces a damaged or worn harness to help regain consistent control response. What it does:

• Routes power and signals between the control switches and the main control board
• Replaces frayed, broken, or corroded wiring that can cause intermittent or no response from panel buttons
• Helps resolve symptoms like unresponsive controls, intermittent operation, or no-start conditions linked to panel wiring
• Maintains original connector fit and routing for correct switch function

• One switch harness assembly as shown

• Disconnect power (unplug or switch off breaker) before starting any work
• Handle connectors carefully and match connector shapes; do not force or modify terminals
• Verify routing and secure clips to prevent rubbing or pinching against moving parts

This control switch is the user-facing rotary selector that lets the appliance select cycles and settings. It restores clear, tactile control so the unit responds correctly when you turn the knob. What it does:

• Selects operating cycles and settings when the knob is turned
• Routes electrical signals from the control panel to the selected function
• Commonly replaced when settings do not change or the control feels loose/slips
• Resolves intermittent or unresponsive cycle selection and erratic behavior

• Disconnect power before attempting any repair to avoid electrical shock
• Accessible from the control panel; remove trim or console as needed per your model's service instructions
• Test function after reassembly; do not force the selector or use excessive torque

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

This wire harness assembly routes power and signals between a range of appliance components to restore reliable electrical connections and proper component operation. Fits as a direct replacement harness used in compatible Whirlpool appliances. What it does:

• Carries power and control signals between control boards, motors, switches and sensors
• Replaces damaged, frayed or corroded wiring that can cause intermittent or failed component operation
• Restores reliable connector-to-connector connections and prevents shorts from exposed wiring
• Helps resolve issues such as intermittent operation, components that won't respond, or visible wiring damage

• Disconnect power to the appliance before starting any repair
• Take photos of the existing harness routing and connector positions to aid reassembly
• Ensure all connectors are fully seated and any retaining clips or straps are secured
• If wiring shows burn, melting, or damaged insulation, replace the harness rather than repairing temporary sections

The Float Switch is an OEM part for Whirlpool dishwashers. It is a safety component that detects water levels and monitors flood conditions. The float switch ensures the dishwasher only runs water when needed and shuts off water flow if it detects a potential leak or overflow situation. 

Symptoms of a bad float switch include: 

• The dishwasher fails to fill with water or stop the water when the cycle is complete
• Loud buzzing or humming noises coming from the float switch area  
• Water leaks inside or outside of the dishwasher due to overfilling
• Repeated error codes related to flooding or water level detection

Causes of a bad float switch could be wear and tear over time, defective wiring or electronic components inside the switch, or damage from moisture or leaks. 

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rocker Switch is an OEM part for Whirlpool refrigerators. This switch is responsible for controlling the operation of your refrigerator's ice maker, allowing you to turn it on or off as needed, providing you with easy control over the ice maker.

A bad switch can occur due to regular wear and tear, electrical issues, or physical damage. If you notice symptoms such as an unresponsive switch, inability to turn the ice maker on or off, or inconsistent ice production, it may be time to replace the rocker switch.

Symptoms of a bad switch include:

• Unresponsive switch
• Inability to turn the ice maker on or off
• Inconsistent or inadequate ice production

Regain control over your Whirlpool refrigerator's ice maker by replacing the faulty or malfunctioning on/off rocker switch with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Refrigerator Door Switch is an OEM replacement part for Whirlpool refrigerators. It is a crucial component that monitors the opening and closing of the refrigerator door, ensuring proper operation and energy efficiency.

Causes of a bad Door Switch can include physical damage, wear and tear over time, or electrical malfunctions.

Symptoms of a faulty Refrigerator Door Switch include:

• Interior lights remaining on even when the door is closed
• Compressor failing to cycle on and off as intended
• Condensation or frost buildup due to improper sealing
• Error codes or warning lights related to the door switch

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

This replacement NC light switch restores proper operation of the appliance's light circuit, helping the light turn on and off as designed for safe use and visibility during service or operation. What it does

• Completes or breaks the light circuit when the door or control triggers the switch.
• Restores interior or indicator light operation that is dim, flickering, or nonfunctional.
• Prevents the light from staying on continuously if the switch is failed closed.
• Matches the OEM function for reliable, long-term use when replacing a worn switch.

• Disconnect power before servicing to avoid shock or injury.
• Access may require removing panels or door trim—refer to your model's service manual or tech sheet.
• Inspect wiring and connectors; replace any damaged harnesses or terminals.

This lid switch assembly kit is the washer's safety interlock. It detects when the lid is closed so the control can allow the machine to spin, helping restore safe, reliable operation when the original switch fails.

• Senses lid closed and enables the spin cycle
• Prevents spinning with the lid open for safety
• Common failure symptoms: no spin or intermittent spin
• Requires pressing or jiggling the lid to run; no audible "click" when closing the lid

• Disconnect power before servicing
• Access the switch under the top/console area; remove the old switch/bracket as designed
• Route wiring along the original path and secure away from moving parts
• Align the actuator so the lid reliably engages the switch; test spin operation before reassembly

This igniter switch assembly replaces a worn or failed switch that controls ignition to a gas burner or oven igniter, restoring reliable spark/ignition and consistent burner operation. What it does

• Acts as the electrical switch that signals the igniter or spark module to light a burner or oven
• Helps resolve intermittent or no-spark ignition symptoms and burners that fail to light
• Restores proper on/off switching for the ignition circuit when the original switch is damaged or worn
• Works as the direct replacement switch component in the ignition system

• One igniter switch assembly

• Disconnect power and shut off gas supply before starting any repair
• Use basic hand tools; handle wiring connectors carefully to avoid damage
• Verify part compatibility with your model before installation

This rotary control switch replaces a worn or failed selector used to change cycles or settings on compatible appliances, restoring reliable user input and exact position selection. Easy-to-replace direct-fit control component. What it does:

• Sends a user-selected position to the appliance control so the unit runs the chosen cycle or setting.
• Replaces a cracked, loose, or non-responsive control shaft or knob interface.
• Stops intermittent or no-response issues when turning the control knob.
• Restores tactile click/position feedback for accurate selection.

• Disconnect power before service to avoid shock risk.
• Access may require removing the control panel.
• Handle the switch and control shaft carefully to avoid damaging terminals or alignment tabs.