Kenmore / Sears Bracket & Flange

Base bracket that holds the leveling foot at the washer cabinet. Replace if cracked, broken, or missing to restore stability and prevent rocking or vibration.

Metal contact leaf for dishwasher switch assemblies. Replace if the original contact is bent, corroded, worn, or missing to restore proper circuit closure.

Replaces cracked or broken mounting bracket in your freezer. Securely holds internal components in proper alignment. Needed when original is damaged.

Secures components to your microwave frame for proper positioning. Replace this bracket if bent, broken, or missing to restore stability and support.

Supports and aligns the refrigerator door at the bottom pivot point. Replace if bent, cracked, or worn to restore proper door alignment and movement.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This small structural bracket supports the "leg" of an interior shelf or drawer assembly in compatible refrigerators. It helps keep shelves level and stable so bins slide smoothly and contents stay secure during everyday use. What it does:

• Supports the corner/leg of an interior shelf, cover, or drawer rail
• Helps maintain level alignment and prevents wobble or sagging
• Restores stability if the original piece is cracked, warped, or missing
• Common symptoms: shelf or drawer sags, binds, or rattles; poor fit/alignment

• 1 supporter leg

• Disconnect power and remove food from the affected area before starting
• Remove the shelf/drawer and note fastener locations or locking tabs
• Transfer any reusable screws/clips and seat the new supporter fully
• Reinstall components, ensuring the shelf/drawer sits level and moves freely

Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.

Secures the heater housing to the dryer cabinet. Replace if your bracket is bent, cracked, or missing to restore stable mounting and alignment.

Links the door button to the latch mechanism for smooth opening. Replace if your lever is cracked, broken, or worn to restore reliable door operation.

The Mounting Bracket is an OEM part for Frigidaire dishwashers. It is a metal component that secures the dishwasher to the surrounding cabinetry. The mounting bracket provides structural support and stability during operation.

Causes of a bad mounting bracket can include damage from installation/removal, cracks or deformities from heavy loads, or broken welds/fasteners holding it in place.

Symptoms of issues with the mounting bracket include:  

• Excessive vibration or shaking of the dishwasher during cycles
• The unit not sitting level or secured properly in the space
• Noises related to movement that shouldn't occur
• Visible damage or instability of the unit 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

Secures the leveling foot to the washer base. Replace if cracked, stripped, or missing to restore a solid mounting point for proper leveling and stability.

A stacking kit that lets you securely mount a compatible dryer on top of a front-load washer to save floor space and improve stability. Designed for factory-specified stacking applications when used with approved appliance pairs. What it does:

• Provides the hardware and brackets needed to secure a dryer to a front-load washer and reduce shifting during use.
• Helps keep stacked appliances aligned for safer operation and less vibration-related movement.
• Intended for factory-approved stacking configurations—ensures the dryer stays fixed to the washer when installed per instructions.
• Can help maximize laundry room space by enabling safe vertical installation where compatible.

• Follow the appliance manufacturer's stacking instructions exactly; use the OEM procedure and supplied template if provided.
• Disconnect power and gas and empty both appliances before starting; wear appropriate safety gear.
• Installation may require two people and basic hand tools; the stacked unit is level and stable after installation.

Secures the lower front kickplate to your refrigerator frame. Replace if clips are broken, cracked, or missing to restore a flush, aligned appearance.

This interlock is the door safety switch assembly that keeps the appliance from running with the door open, restoring proper door sensing so the unit only operates when the door is fully closed. What it does

• Acts as the door safety switch to interrupt power or start signal when the door is open.
• Prevents the appliance from starting or running if the door won't latch or the switch fails.
• Common symptom: appliance does not start or stops immediately when the door is closed or opened.
• Useful when replacing a worn or damaged door latch/switch that causes intermittent operation.

• Disconnect power (unplug or switch off at the breaker) before servicing to avoid shock or injury.
• Access typically requires removing the appliance's front or control panel; keep track of fasteners and wire locations.
• Handle electrical connectors carefully; inspect wiring and connectors for damage before reconnecting.
• Test the switch with a multimeter.

Secures your range to the wall or floor to prevent tipping when the oven door is opened. Replace if missing, broken, or during new installation.