Kenmore / Sears Bumper, Bushing, Grommet Parts

A small sleeve used to support and align a shaft, pin, or lever inside the appliance. Replacing a worn bushing restores smooth, quiet movement and helps prevent accelerated wear on adjoining parts for reliable operation. What it does:

• Supports and centers a rotating or sliding shaft/pin
• Reduces friction and metal-to-metal wear to minimize noise
• Helps maintain proper alignment for consistent performance
• Common signs of wear: wobbling play, squeaks/grinding, binding, or visible cracks

• One bushing

• Disconnect power and shut off gas/water before servicing
• Note the original orientation; seat the new bushing fully and squarely
• Clean mating surfaces; inspect shafts/pins for wear and replace if damaged
• Apply manufacturer-approved lubricant only if specified by your service manual

Color: White

Note: For Black, order WP67002721. For Grey, order W11245157. 

This cam plate is the stamped metal guide that secures and locates the dryer drum, helping maintain smooth rotation and proper alignment. Replaces a worn or damaged cam that can cause noise, rubbing, or uneven drum movement. What it does:

• Positions and guides the dryer drum to prevent lateral movement and maintain alignment.
• Absorbs and transfers load between the drum and the rear support assembly for stable rotation.
• Reduces metal-on-metal contact that can cause squeaks, scraping, or worn drum edges.
• Helps restore smooth drum tracking when a broken or worn cam causes rubbing or off-center rotation.

• One cam plate

• Disconnect power before starting any repair to prevent shock or injury.
• Access typically requires removing the dryer front or top panel and supporting the drum; follow OEM service manual steps.
• Inspect associated rollers, glides, and mounting hardware and replace if worn to prevent repeat failure.
• Tighten fasteners to OEM torque and verify proper drum rotation before full reassembly.

This rubber lid bumper cushions the washer lid to prevent hard contact and reduce noise and wear. It replaces a worn or missing bumper to help the lid close more softly and sit level. What it does:

• Acts as a soft contact point between the lid and cabinet to absorb impact
• Reduces lid slamming, rattling, and vibration during operation
• Helps keep the lid aligned and prevents cosmetic damage to the rim
• Commonly replaced when the bumper is cracked, flattened, or missing

• One rubber lid bumper

• Install by removing the old bumper and pushing the new bumper into the mounting hole or recess; hand tools may be helpful
• Ensure the appliance is powered off and disconnected before servicing
• Inspect surrounding mounting area for damage and replace any broken retainers as needed
• If the bumper is hard to seat, warm it briefly with a hair dryer to improve flexibility

This rubber grommet cushions and protects components by isolating vibration and preventing wear where parts pass through openings. It restores proper fit and reduces noise or rubbing caused by a worn or missing grommet. What it does:

• Cushions panels, housings, or shafts to reduce vibration and noise
• Protects wiring, hoses, or metal edges from abrasion where they pass through openings
• Keeps assemblies aligned by filling mounting gaps and securing components
• Common symptom: increased rattling, vibration, or chafing around the affected area

• One rubber grommet

• Disconnect power to the appliance before beginning any repair
• Remove panels or components as needed to access the grommet; hand tools may be sufficient
• Inspect surrounding parts and replace any damaged items
• Use the OEM-style grommet to ensure proper fit and function

This cam timer is the mechanical control that sequences an appliance's cycles, restoring correct timing and function when the control knob stops advancing. Replace a worn or stuck timer to recover proper cycle progression and operation. What it does:

• Advances cycle stages by rotating cams that open and close control contacts
• Sends timed signals to motors, switches and circuits to start and stop functions
• Common symptom: cycles won't advance or unit stays stuck in one cycle
• Common symptom: timer won't turn or control knob feels loose/slips

• One replacement cam timer assembly

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control console or rear panel; use proper tools
• Note original timer position and knob alignment before removal for correct reassembly
• Test appliance through a full cycle after installation to ensure proper operation

This small rubber grommet cushions and secures a range or oven door handle, helping keep the handle stable and reducing wear where the handle meets the door. It restores a snug fit and quiet operation. What it does:

• Acts as a protective bushing between the handle and door to prevent metal-on-metal contact
• Helps stop a loose, wobbly, or rattling handle
• Reduces wear on mounting holes and finish around the handle
• Provides a tight, vibration-dampening fit for the handle assembly

• Disconnect power to the appliance before starting any work
• Typically a simple press-fit replacement; handle removal may be required for access
• Inspect surrounding fasteners and mounting surfaces; replace damaged parts as needed