Kenmore Elite Parts

Replaces your washer's door boot gasket that seals the drum opening. Install when you notice leaks, mold buildup, or cracks. Confirm fit with your model.

Loud grinding or rattling from your oven? A damaged convection fan blade disrupts airflow. This replacement restores quiet operation in 20-30 minutes.

This is a 1450-watt hidden bake element located beneath the floor of the oven cavity. It provides the primary heat source for baking and roasting. Replace this element if the oven is not heating from the bottom, takes too long to reach temperature, or cooks food unevenly.

Replace your range oven door gasket to prevent heat escape and maintain proper temperature. Snaps into place with embedded clips. Confirm fit by model.

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This is an oven bake igniter that mounts inside the oven compartment near the bake burner. It draws electrical current to heat up and open the gas valve, allowing the bake burner to light. Replace this part if your oven takes a long time to heat up, doesn't reach the set temperature, or fails to ignite at all.

This surface burner ignitor/orifice assembly directs gas through a calibrated orifice and provides the spark to ignite it. Replacing a worn or damaged assembly restores consistent lighting and an even flame on the affected rangetop burner.

• Routes gas from the valve through the orifice to the burner head
• Positions the ignitor for reliable sparking and quick ignition
• Helps maintain correct flame size and pattern on that burner
• Common symptoms: burner won't light, clicks without flame, delayed ignition, weak or uneven flame

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner heads; lift the cooktop to access the assemblies
• Note wire routing and original orifice location; transfer any reusable hardware from the old part
• After installation, restore gas and check connections for leaks, then test spark and flame

Fix F10 error codes, blank displays, or temperature fluctuations. This oven control board restores bake/broil cycles and keypad response in your range.

Gasket for upper wheel.

Protects refrigerator light bulbs and sockets from moisture and impacts. Replace if cracked, melted from bulbs staying on, or discolored. Confirm fit.

Replace cracked, shattered, or broken door glass on your range or oven. This glass panel installs in the door assembly to provide insulation and visibility.

Fix a broil burner that won't light or clicks repeatedly. This spark electrode generates the ignition spark needed for reliable broil operation.

Front leveling foot adjusts range height for stability. Replaces cracked, broken, or missing feet. Ensures proper leveling to reduce vibration.

Burner orifice regulates gas flow to your range burners. Replace if clogged with debris, corroded, or damaged to restore proper combustion and heat output.

Dryer drum seal creates an airtight barrier between the rotating drum and housing to maintain drying efficiency. Replace if cracked or hardened. Verify fit with your model number.

The Dishrack Track (Right) is an OEM part for Whirlpool dishwashers. It is responsible for supporting the third-level dishrack and allowing it to glide in and out smoothly during the loading and unloading process. This track is designed specifically for the right side of the third-level rack. 

Causes of a bad track include damage from heavy use over time, such as dulling or bending of the metal track surface from repeated loading/unloading of dishes. Debris or residue buildup along the track can also cause issues.

Symptoms of a bad track include:  

• Rack that will not fully extend or retract
• Binding or sticking during rack movement  
• Rack that will not stay positioned above

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.