Kenmore / Sears Fuse Or Sensor

Genuine Ge part

Kenmore Fuse (Ccmr 30A, 120V)

By: Ge

Part Number: WE1M1002

This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.

Provides overcurrent protection for the circuit specified by the manufacturer
If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
Helps prevent wiring and component damage from shorts or overloads
Repeated fuse failures indicate an underlying electrical issue requiring diagnosis

What's included: 1 CCMR fuse (30A, 120V) Install notes:

Disconnect power to the appliance before servicing
Locate the fuse in its holder/block and inspect associated wiring for heat or damage
Test the old fuse for continuity; replace only with the identical rating specified
Never bypass or upsize a fuse; correct the root cause of the failure before returning to service

Do-It-Yourself Stories from Customers like You The dryer would not turn on Roland S. • Richmond , CA • August 02, 2014

First I check the breaker for the dryer then I check the power cord and the ohms to the power cord when all this things were in working order I then check the ohms to the fuse to the control panel. The fuse had no ohms so I got a pair on needle nose pliers pulled out the fuse and replace it worked just find after that Read more

$53.69

Compare At:: $63.89
You Save:: $10.20

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Frigidaire part

Kenmore Dryer Cycling Thermostat

5.0 (4)

By: Frigidaire

Part Number: 131298300

Dryer won't heat or overheats? A failed cycling thermostat can't regulate temperature. This direct-fit part takes 15–30 minutes to replace.

This part fixes the following symptoms

Too hot

Do-It-Yourself Stories from Customers like You Rubbing blocks and felt that seal the front of the drum are worn drum is sagging and staining clothes with smears of rust Seth W. • Upper Arlington , OH • January 23, 2016

Replaced upper and lower felts. Painted rubbing surface on inside of drum with refrigerator enamel. Took out drum and lubed rear bearing. Replaced 2 of the 3 thermostats, and the belt just on principle. Spent a lot of time with shop-vac removing lint from drier and exhaust ducts. Runs great and is no longer cooking or staining clothes. Read more

$50.57

Compare At:: $60.68
You Save:: $10.11

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Frigidaire part

Kenmore Oven Thermal Switch

5.0 (1)

By: Frigidaire

Part Number: 318004900

Oven won't heat or can't hold temperature? This thermal switch monitors oven temperature and protects internal components. Common fix for heat issues.

Do-It-Yourself Stories from Customers like You Oven would not hold temperature Catherine U. • Richmond Hill , GA • November 16, 2015

After 2 repair men, many parts replace it still didn't work, Did research on line and found out the thermal fuse would need to be replace.. Read more

$52.68

Compare At:: $148.85
You Save:: $96.17

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Whirlpool part

Kenmore Dishwasher Thermal Fuse

4.8 (5)

By: Whirlpool

Part Number: WP3368928

Dishwasher won't heat or dry dishes? A blown thermal fuse cuts power to the heating circuit. Easy plug-and-play fix—most DIYers replace in minutes.

Do-It-Yourself Stories from Customers like You Heated dry wouldn't work Steven L. • Fenton , MI • June 13, 2014

I took a multimeter and found out that the old fuse was open. I ordered this new one and popped it in. Pretty easy fix and it's still going strong. Read more

$60.21

Compare At:: $62.40
You Save:: $2.19

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Frigidaire part

Kenmore Moisture Sensor (Dryer)

5.0 (5)

By: Frigidaire

Part Number: 134786110

This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:

Detects moisture level via conductivity across the sensor surfaces inside the drum
Sends feedback to the control so Auto Dry cycles advance and stop correctly
Helps prevent overdrying and underdrying in sensor-based cycles
Common symptoms of a faulty sensor may include: auto cycles ending too soon or running too long, clothes remaining damp, or the dryer staying on "Sensing" while timed cycles still work

What's included:

1 moisture sensor

Install notes:

Disconnect power and, if applicable, shut off gas before servicing
Access the sensor at the front bulkhead/lint housing area; remove front panel as needed per model
Transfer connectors and route wiring exactly as original; secure the sensor firmly
Clean the sensor contact surfaces with rubbing alcohol; residue from dryer sheets or fabric softeners can affect readings

Do-It-Yourself Stories from Customers like You Clothes got stuck on moisture sensor bar and broke it off Felix M. • Kyle , TX • April 17, 2015

Fixed it in 5minutes. One end has a Phillips head screw and the other has a tab with to metal leads for wires. The end with the tab broke. I removed the screw for the other end abd the sensor bar came off. To put the new piece on, I connected the wires to the leads, slid the tab end into place on the drum and screwed in the other end. Done! Easy! Read more

$75.95

Compare At:: $90.38
You Save:: $14.43

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Whirlpool part

Kenmore Electrode

By: Whirlpool

Part Number: W11165163

The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.

A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.

Symptoms of a bad electrode include:

Clothes taking longer to dry than usual
The dryer shutting off prematurely
Inconsistent drying results, with some items remaining damp

Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

$50.57

Compare At:: $60.18
You Save:: $9.61

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Whirlpool part

Kenmore Dryer Cycling Thermostat

5.0 (6)

By: Whirlpool

Part Number: WPY304474

If your dryer takes too long to dry or overheats, the cycling thermostat may have failed. This part regulates heat by cycling on and off. Easy DIY fix.

This part fixes the following symptoms

No heat or not enough heat

Do-It-Yourself Stories from Customers like You It was taking unusually long to dry a typical load Robert L. • Williamsburg , VA • November 15, 2014

I removed the front panel and observed the heating element while running the dryer. It was cycling off every minute or so and staying off for several minutes. Even though it was likely the high temp cycling thermostat I replaced both the 14, and 15 cycling thermostats which I think are the original factory units. That makes them nearly 35 years old. Problem fixed. Read more

$54.25

Compare At:: $65.10
You Save:: $10.85

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Lg part

Kenmore Washer Water Temperature Sensor

4.0 (1)

By: Lg

Part Number: 6322FR2046G

Washer not heating water or showing tE error? This temperature sensor monitors water temp and signals the control board. Moderate DIY repair fixes temp issues.

Do-It-Yourself Stories from Customers like You Te error code on my kenmore elite washer Angela R. • Rushville , IN • February 08, 2015

Ordered a new thermistor and replaced the one that the wires had pulled out of. Note- we secured the wires on the new thermistor with electrical tape before installing. Read more

$38.28

Compare At:: $45.55
You Save:: $7.27

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Samsung part

Kenmore Microwave Thermostat

4.9 (15)

By: Samsung

Part Number: DE47-20007B

Microwave has no power or won't start? A faulty cavity thermostat often causes complete shutdowns. This part restores temperature control in 5-10 minutes.

Do-It-Yourself Stories from Customers like You Smh1816s samsung microwave went completely dark no controls no lights receptacle good John S. • Olathe , KS • March 17, 2015

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

$10.71

Compare At:: $12.74
You Save:: $2.03

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Frigidaire part

Kenmore Turbidity Sensor (Dishwasher)

5.0 (1)

By: Frigidaire

Part Number: 154762601

This dishwasher turbidity sensor measures how dirty the wash water is and reports to the control. Replacing a faulty sensor can restore proper cycle times and cleaning performance for consistent results.

Monitors water clarity/soil level during the wash
Sends feedback to the control to adjust cycle length, rinses, and heating
Failure can cause very long or very short cycles
Can trigger sensor-related fault indications

What's included: One sensor Install notes:

Disconnect power at the breaker and shut off water before servicing
Access the sensor from the bottom near the sump; remove the toe panel if needed
Unplug the wire harness; release the locking tabs or twist-lock to remove; avoid touching the optical window
Inspect and reuse the existing seal/retainer if in good condition; seat fully and check for leaks after reassembly

Do-It-Yourself Stories from Customers like You Leaking from the door and around the sensor gasket. Michael S. • Franklin , WI • May 07, 2023

I replaced the sensor and the seals around the door. Read more

$63.65

Compare At:: $75.11
You Save:: $11.46

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Whirlpool part

Kenmore Ice Maker Thermistor Assembly

4.5 (2)

By: Whirlpool

Part Number: WP2313635

Ice maker not producing ice or overflowing? Failed thermistor prevents proper temperature monitoring. Direct plug-in replacement restores ice production.

Do-It-Yourself Stories from Customers like You The ice maker was making very small ice cubes with a cloudy appearance Igal E. • Memphis , TN • January 01, 2017

There are plenty of DIY youtube videos to show you how to replace the parts. I went ahead and replaced more than just the broken parts. I figured if I had the machine opened up, I might as well replace parts that could go out in the future. I might have gone a bit too far with all the other parts. The only part that was really broken was the wiring harness. Two of the wires had corroded from the sockets and there was no other way than to replace the entire harness. Its a bit tricky to feed... Read more

$63.65

Compare At:: $75.74
You Save:: $12.09

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Whirlpool part

Kenmore Thermostat (Internal-Bias)

By: Whirlpool

Part Number: WP3387138

This internal-bias thermostat controls exhaust temperature in your dryer, cycling the heat on and off to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent drying performance and help protect the dryer from overheating shutdowns.

Monitors exhaust air temperature and opens/closes the heating circuit to regulate heat
Provides the bias function used by automatic cycles for correct temperature control
Failure symptoms can include no heat or low heat, long dry times, overheating or high-limit trips, and inconsistent cycling temperatures
Helps prevent thermal cutoffs caused by restricted airflow or faulty temperature regulation

What's included: 1 internal-bias thermostat

Disconnect power before servicing; for gas models, also shut off the gas supply
Access location is typically on the blower/exhaust housing; note wire positions and transfer one at a time
Ensure the thermostat mounts flush for proper sensing; tighten screws securely
After replacement, verify good airflow and clear venting to prevent repeat failures

$66.78

Compare At:: $79.47
You Save:: $12.69

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Whirlpool part

Kenmore Dryer High-Limit Thermostat

4.9 (9)

By: Whirlpool

Part Number: 279054

Dryer not heating or running too hot? This high-limit thermostat regulates temperature to prevent overheating. Easy DIY fix takes 30 minutes or less.

Do-It-Yourself Stories from Customers like You Dryer would come on but would not heat John H. • Westfield , NY • January 23, 2015

FIRST I PULL THE DRYER OUT FROM THE WALL AND TOOK THE BACK OFF. WITH A 5/16 NUT DRIVER. NEXT WITH A LIGHT SET UP I LOOKED FOR ANY BURNT, BROKEN,OR LOSE WIRES THAT MY HAVE COME OFF ANY CONNECTIONS. I HAVE AN ELECTRIC DRYER AND AS I LOOKED DOWN TO THE HEATING COIL AREA, WHAT I WILL CALL A HI-TEMP SWITCH I COULD SEE THAT THE PART APPEARED BURNT. I PULLED THE POWER PLUG AND TOOK MY VOLT, OHM, MIL'LI'AMP METER, SET IT TO OHMS ON ABOUT 20K. THEN I TOOK MY NEEDLE NOSE PLIERS AND PULLED ONE WIRE... Read more

$51.35

Compare At:: $60.91
You Save:: $9.56

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Frigidaire part

Kenmore Dryer Control Thermostat

5.0 (4)

By: Frigidaire

Part Number: 134048800

Dryer overheating or taking too long to dry? This control thermostat regulates internal temperature by cycling the heater on and off. Easy replacement.

Do-It-Yourself Stories from Customers like You My dryer was taking too long to dry my clothes. Gerard C. • Millville , MA • March 08, 2017

I replaced both thermostats, the seals and the heating element and the belt. It's an easy job to keep my dryer last longer. Read more

$78.95

Compare At:: $94.74
You Save:: $15.79

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Lg part

Kenmore Microwave Humidity Sensor Assembly

5.0 (1)

By: Lg

Part Number: 6501W1A013A

Fix F4 error codes or sensor cook failures with this microwave humidity sensor. Restores automatic cooking cycles. Moderate DIY difficulty.

Do-It-Yourself Stories from Customers like You Microwave would not microwave Richard E. • Cape Coral , FL • January 05, 2020

Replaced the Humidity sensor, Thermistor and door switches. I replaced these thinking the problem was one of the items but didn't want to trial and error one part at a time. Plus the cost was reasonable so if these didn't help I wasn't out a lot of money. I sense the door switch was the problem. Replaced all items and the microwave works great. Thanks for the advice and the cost of the parts. Read more

$74.95

Compare At:: $89.19
You Save:: $14.24

IN STOCK

Ships Today Guaranteed

Add to Cart

Genuine Ge part

Kenmore Dryer Thermostat

By: Ge

Part Number: WE4M127

Fix a dryer that won't heat, overheats, or runs too long. This thermostat cycles the heating element to maintain safe drying temperatures.

$18.95

Compare At:: $28.41
You Save:: $9.46

IN STOCK

Ships Today Guaranteed

Add to Cart

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Kenmore / Sears Fuse Or Sensor

Kenmore Fuse (Ccmr 30A, 120V)

Kenmore Dryer Cycling Thermostat

Kenmore Oven Thermal Switch

Kenmore Dishwasher Thermal Fuse

Kenmore Moisture Sensor (Dryer)

Kenmore Electrode

Kenmore Dryer Cycling Thermostat

Kenmore Washer Water Temperature Sensor

Kenmore Microwave Thermostat

Kenmore Turbidity Sensor (Dishwasher)

Kenmore Ice Maker Thermistor Assembly

Kenmore Thermostat (Internal-Bias)

Kenmore Dryer High-Limit Thermostat

Kenmore Dryer Control Thermostat

Kenmore Microwave Humidity Sensor Assembly

Kenmore Dryer Thermostat

Appliance Type

Popular Kenmore Models

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Kenmore / Sears Fuse Or Sensor

Appliance Type

Popular Kenmore Models

We respect your privacy

Manage consent preferences