Kenmore / Sears Hose Or Tube

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Size: 7 foot long.

This replacement 5/16-inch icemaker tubing carries water to the ice maker. It helps restore proper flow and reduce leaks when the original line becomes brittle, cracked, or kinked, improving ice production reliability. What it does:

• Carries water from the inlet valve to the icemaker
• Replaces tubing that is brittle, cracked, or kinked
• Helps restore normal icemaker fill and ice production
• Can help stop leaks caused by a damaged water line

• 1 icemaker water tube (5/16 in.)

• Unplug the refrigerator and shut off the water supply before servicing
• Place a towel or container to catch residual water during line removal
• Route the new tube along the original path; avoid sharp bends and hot or moving components
• Tighten all fittings, restore water, and check all connections for leaks before powering on

This refrigerator drain tube channels defrost water from the evaporator to the rear drain pan so it can evaporate. Replace a cracked, missing, or clogged tube to stop interior leaks and ice buildup.

• Routes defrost meltwater from the freezer drain to the condenser drip pan
• Helps prevent pooling under crisper drawers or water on the floor
• Common failure symptoms: water under drawers, ice sheet in the freezer bottom, recurring drain clogs or freeze-ups, dripping at the rear base
• Restores proper drainage when the original tube is brittle, split, or obstructed

• Disconnect power; pull the unit forward and remove the lower rear access panel
• Remove the old tube from the drain outlet and drip pan; clear any ice/debris with warm water—avoid sharp tools
• Seat the new tube fully on the drain outlet and position the outlet into the pan; verify flow by pouring warm water down the drain
• Restore power and monitor for leaks as normal defrost cycles resume

This replacement injection tube routes water through the refrigerator's supply system to the ice maker or dispenser, as designed for your model. Replacing a cracked or kinked tube restores proper flow and helps prevent leaks.

• Channels water from the inlet circuit to its destination component (ice maker or dispenser, per design)
• Helps maintain a sealed path for clean, reliable water delivery
• Common symptoms: water leaking inside/behind the refrigerator
• Dispenser has slow/no flow
• Ice maker not filling or producing small/hollow ice; visible cracks, kinks, or brittle tubing

• Unplug the refrigerator and shut off the household water supply before servicing
• Note the original routing and connector types; transfer any reusable fittings or clamps from the old tube
• Insert the tube fully into existing connectors or onto barbed fittings and secure with the original clips/clamps
• Restore water, check all joints for leaks, then power on and test the dispenser/ice fill

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

Size: 21 inches long. Clamp included.

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

This manifold channels wash water within the dishwasher's spray system. Replacing a damaged or clogged manifold helps restore proper water flow and cleaning performance while reducing the chance of leaks at internal connection points.

• Routes high-pressure wash water through the dishwasher's spray system
• Maintains a sealed path to help prevent internal leaks
• Supports consistent spray pressure for effective cleaning coverage
• Helps resolve symptoms such as poor cleaning, weak spray, leaks, or visible cracks in the manifold

• Disconnect power and turn off the water supply before servicing
• Access from inside the tub; remove racks or panels as needed to reach the manifold
• Release retaining clips/screws and note the manifold's orientation; inspect any related seals/O-rings and replace if worn
• Reassemble and run a short cycle to check for proper spray and leaks

This short connector hose links internal dishwasher plumbing to move water securely between components. Replacing a worn or cracked hose helps prevent leaks and keeps cycles running reliably. What it does:

• Routes water between two internal connection points during the wash cycle
• Helps maintain a watertight seal when properly clamped
• Common symptoms: water leaking beneath the unit, dampness around hose joints, visible cracks/hardening, or a loose fit
• Aging hoses can stiffen and drip at barbed fittings

• 1 connector hose

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and pull the dishwasher forward as needed to access the hose
• Expect a small amount of residual water; have towels or a shallow pan ready
• Fully seat the hose on fittings, secure with appropriate clamps, then run a brief cycle and check for leaks

This replacement tube carries water from the inlet valve into the refrigerator's icemaker. An intact fill tube helps route water cleanly to the mold, reducing leaks, drips, and ice build-up around the fill area.

• Directs water into the icemaker fill cup/mold during the fill cycle
• Helps seal the cabinet pass-through to prevent leaks and frost intrusion
• Replaces tubes that are cracked, kinked, or blocked by ice/mineral deposits
• Symptoms may include no ice or small cubes, water dripping/ice sheet in the freezer, or frost near the fill tube

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the icemaker as needed, clear any ice from the fill opening, and pull the old tube from the cabinet port
• Insert the new tube fully, align it with the icemaker fill cup, and reconnect the water line
• Restore water and power, then check for proper fill and leaks

Size: 1/4" to 1/4" John Guess coupler. Compression fitting is also acceptable.

This right-angle elbow fits between the water supply line and the refrigerator's icemaker fill tube. It directs water cleanly into the icemaker and helps maintain a sealed connection to reduce drips and leaks. What it does:

• Connects the inlet water tubing to the icemaker fill tube at a 90-degree angle
• Routes water into the icemaker during the fill cycle
• Helps maintain a watertight connection at the rear of the cabinet
• Common symptoms: leaking behind the refrigerator, slow or no ice production, ice buildup near the fill area

• 1 fill tube elbow fitting

• Unplug the refrigerator and turn off the water supply; relieve line pressure before starting
• Access the rear lower area, place a towel for any residual water, and locate the elbow at the fill tube connection
• Release the clamp or retainer, disconnect the tubing, seat the new elbow fully, and resecure the line
• Turn water back on, check for leaks, then restore power and monitor the first ice fill

This stainless-steel braided dishwasher connector links your home's water supply to the dishwasher inlet. The 72-inch length and 3/8 in Comp x 3/8 in MIP fittings provide a durable, properly sized connection for installations using these ends.

• Connects the shutoff/angle stop to the dishwasher inlet
• 72-inch length accommodates routing through cabinets and tight spaces
• Braided stainless-steel jacket for durable service
• Replace if you notice leaks at the hose or fittings, visible corrosion/fraying/kinks, or slow/no fill from restriction

• Disconnect power and shut off water at the supply valve before starting
• Place a towel or pan to catch residual water
• Start all threads by hand to avoid cross-threading; tighten with a wrench until snug—do not overtighten
• Use thread sealant only on tapered pipe threads if required; do not use on compression seats. Open the valve slowly and check for leaks.

This drain hose carries used water from the appliance to the household drain. A secure, leak-free drain path helps prevent water from backing up or leaking during and after a cycle.

• Routes wastewater from the unit to the standpipe or sink drain
• Helps resolve issues like slow or incomplete draining
• Can address leaks found around the rear or drain area
• Restores proper water exit flow after hose damage or kinks

• Unplug power and shut off water before servicing
• Have a towel or shallow pan ready to catch residual water
• Note hose routing and connections before removal; transfer any clamps if reused
• Ensure tight, watertight connections and proper routing without kinks

This chute channels water and wash additives from the dispenser housing into the tub. Replacing a damaged or clogged chute helps ensure proper dispensing and reduces leaks or residue around the dispenser area. What it does:

• Guides detergent/bleach/fabric softener from the dispenser to the wash tub
• Maintains proper flow to prevent backups at the dispenser drawer
• Helps reduce leaks and drips from the dispenser area
• Common failure symptoms include water backing up into the drawer, detergent residue left in the dispenser, or leaks at the front-left/top of the washer

• 1 chute

• Disconnect power and turn off water supply before servicing
• Access is typically from the top; remove panels as needed to reach the dispenser assembly
• Transfer any seals, clamps, or hardware from the old chute
• Reassemble and run a brief fill/rinse to check for proper flow and leaks