Kenmore / Sears Insulation, Sound Dampening Parts

This molded cabinet liner insulation reduces heat transfer around the refrigerator cavity to help maintain steady temperatures and improve cooling efficiency. Designed to replace worn or damaged insulation that can allow frost buildup or increased run time. What it does

• Fills the airspace between the outer cabinet and inner liner to slow heat gain
• Helps the cooling system maintain consistent internal temperatures
• Can reduce frost accumulation caused by damaged or missing insulation
• Restores the original thermal barrier after repair or after removing interior components

• One pre-formed cabinet liner insulation piece

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels, and fasteners as needed to access the insulation cavity
• Handle gently to avoid compressing or tearing the material; fit into existing channels or adhesive points
• If adhesive is required, use manufacturer-recommended high-temperature adhesive or fasteners

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

This cabinet insulation helps reduce heat transfer inside the refrigerator, supporting stable temperatures and efficient cooling. Replacing damaged or missing insulation can improve temperature control and reduce frost buildup. What it does:

• Fills gaps between the cabinet and liner to slow heat transfer and maintain internal cold
• Helps the appliance reach and hold set temperatures more consistently
• Reduces condensation and excess frost on interior surfaces
• Can improve compressor run-time and overall energy efficiency when intact

• Disconnect power before starting
• Remove food and shelving from the compartment before accessing the insulation
• Handle insulation carefully to avoid tearing; secure per manufacturer routing and adhesive points
• Dispose of old insulation per local regulations

This absorber is the factory-design replacement part that restores the appliance's intended absorption function, helping maintain normal operation and reduce related performance issues. What it does:

• Absorbs and manages moisture/condensate or trapped vapors in the appliance's system to support normal function.
• Helps prevent symptoms commonly linked to a failed absorber, such as excess moisture, unusual odors, or intermittent system cycling.
• Restores the original fit and function when the installed absorber is cracked, broken, or heavily degraded.
• Matches OEM shape and connection points for a direct replacement.

• One absorber replacement as shown

• High-level replacement: access the absorber location; no specialized calibration typically required.
• Disconnect power (and water supply if applicable) before removing panels or replacing parts.
• Handle carefully to avoid damage to surrounding components and wiring; use manufacturer-recommended fasteners.

This vibration dampener cushions and isolates vibrating components to reduce noise and movement, helping your appliance run more quietly and smoothly. It's a simple replacement that restores proper mounting and stability. What it does:

• Absorbs vibration from compressors or motors to cut down on rattling and buzzing
• Keeps mounted components aligned and prevents metal-to-metal contact
• Helps reduce transfer of vibration into the cabinet and surrounding surfaces
• Commonly replaced when excessive noise, shaking, or loose mounts are present

• One vibration dampener

• Disconnect power to the appliance before servicing
• Support the component (compressor/motor) before removing mounts to avoid shifting
• Typically press-fit or bolted into place; use basic hand tools as required
• Replace any damaged fasteners and secure mounting before restoring power

This dampener regulates airflow inside the refrigerator to help steady temperatures between compartments and reduce temperature swings. It replaces a worn or broken air control piece to restore proper circulation and consistent cooling. What it does:

• Controls airflow between fridge compartments to help maintain even temperatures
• Helps reduce warm or cold spots caused by stuck or broken dampeners
• Minimizes rapid temperature changes when doors open and close
• Operates quietly as part of the internal air distribution system

• Disconnect power to the appliance before starting any repair
• Basic hand tools may be required; handle plastic parts carefully to avoid breakage
• Verify correct orientation and secure mounting for proper airflow operation

This foam insulation block helps fill gaps and reduce heat transfer inside the refrigerator cabinet to maintain proper cooling and reduce frost/condensation. It restores the designed insulation barrier where the original piece is damaged or missing. What it does:

• Replaces a damaged or missing foam block that seals internal gaps in the cabinet or behind panels
• Helps prevent warm air infiltration that can cause poor cooling or excess frost
• Reduces condensation and moisture buildup around the evaporator area or panel seams
• Supports consistent temperature performance by restoring insulation continuity

• One foam insulation block

• Disconnect power to the appliance before beginning any repair
• Access location may require removing interior panels or shelves; handle panels and clips carefully
• Install in the exact position and orientation of the original part; use any existing adhesive or fasteners as required
• If adhesive is needed, use only appliance-safe adhesives compatible with foam and follow manufacturer guidance

This sound absorber is an OEM-style insulation pad designed to reduce washer cabinet noise and rattling for a quieter cycle. It mounts inside the appliance cabinet to help dampen vibration and airborne sound. What it does:

• Dampens vibration and reduces cabinet noise during spin and agitation
• Helps minimize rattling from internal components for a quieter operation
• Supports stable operation by providing a cushioned barrier between parts and the cabinet
• Commonly replaced when padding is torn, missing, or compressed

• One sound absorber insulation pad

• Disconnect power and water supply before starting any repair
• Access may require removing outer cabinet or panels; follow your model's service manual
• Use proper fasteners and placement as shown in OEM diagram; avoid altering material

This oven back insulation is the replacement rear cavity pad that helps contain oven heat and protect rear components and cabinetry. It restores proper thermal barrier performance for safer, more consistent oven operation. What it does:

• Provides a thermal barrier behind the oven cavity to limit heat transfer to the rear panel and surrounding cabinetry
• Helps maintain more consistent cooking temperatures by reducing heat loss through the back
• Protects wiring, controls, and exterior surfaces from excessive heat exposure
• Replaces missing, damaged, or deteriorated insulation that can cause higher rear-surface temperatures or heat-related odors

• One oven back insulation pad as shown

• Disconnect power to the appliance before servicing
• Remove the range/oven from its enclosure and access the rear panel per your model's service instructions
• Handle insulation with gloves and a mask if fibers are exposed; avoid compressing or tearing the material
• Secure the insulation in the original position with factory fasteners or clips; verify no obstruction of vents or wiring before reassembly

Side

Bottom