Kenmore / Sears Relay, Overload, Capacitor

Fixes refrigerator not cooling with hum-click sound from compressor. This PTC start device energizes the compressor start winding. DIY repair in 10 minutes.

This controller is the refrigerator's electronic brain, managing cooling and defrost operations to keep temperatures stable. Replacing a failed board restores reliable compressor, fan, and defrost control when cooling becomes erratic.

• Regulates compressor and evaporator fan operation to maintain set temperatures
• Manages the defrost cycle to prevent frost/ice buildup on the evaporator
• Coordinates inputs from sensors/switches for consistent, efficient cooling
• Common failure symptoms include poor or intermittent cooling, heavy frost on the back wall/evaporator, constant running or short-cycling, or failure to start

• Disconnect power before servicing and use ESD precautions when handling electronics
• Access the control location (typically in the control housing or rear compartment) and photograph wiring for reference
• Transfer connectors one at a time to the new board; ensure all plugs are fully seated and harnesses are routed safely
• Reassemble panels, restore power, and verify normal compressor/fan operation

This kit includes the start relay and overload protector that help the compressor motor start and run properly. The relay provides the initial electrical boost to get the compressor running, while the overload protector shuts it off if it draws too much current or overheats. Replace this kit if the refrigerator or freezer is not cooling, the compressor clicks on and off repeatedly, or you hear a buzzing sound coming from the back of the unit.

The Starter is an OEM replacement part for Frigidaire refrigerators. This component is crucial for initiating the compressor, which is responsible for cooling the refrigerator. The starter works by providing the necessary electrical power to get the compressor running, ensuring that the refrigerator maintains the correct temperature.

Causes of a bad starter can include electrical malfunctions, wear and tear over time, or damage from power surges. A faulty starter can prevent the compressor from starting, leading to cooling issues.

Symptoms of a bad Starter include:

• The refrigerator not cooling properly
• The compressor not running or frequently cycling on and off
• Unusual clicking or buzzing noises from the compressor area
• The refrigerator being warmer than usual or food spoiling quickly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Compressor Controller is an OEM part for Frigidaire refrigerators. It is a component responsible for monitoring and regulating the compressor.

The controller allows the compressor to operate efficiently based on temperature inputs from sensors located throughout the refrigerator and freezer compartments. It controls compressor cycling intervals based on sensor readings in order to maintain optimal cooling.

Symptoms of a faulty controller include:

• Fluctuating interior refrigerator temperatures
• Compressor runs continuously without cycling off
• Compressor fails to turn on at all

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This controller kit replaces the appliance's electronic control board, restoring proper power-up, keypad/display response, and reliable operation of controlled functions. Use it to address unresponsive controls or erratic behavior caused by a failed control board. What it does:

• Manages operation of key components based on sensor inputs and user settings
• Processes keypad/remote commands and powers display, mode, and timer circuits
• Coordinates temperature feedback to maintain selected settings
• Common failure symptoms include no display, unresponsive buttons, will not start, intermittent cycling, or error codes

• One controller kit

• Disconnect power before servicing; allow capacitors to discharge
• Use ESD precautions; handle the board by the edges only
• Access the control compartment; photograph wiring and move connectors one at a time to the new board
• Securely mount the board, restore power, and test all functions

This capacitor stores and releases electrical energy to support the appliance's circuit during startup and operation. Replacing a weakened capacitor can restore reliable performance and reduce humming, hard starting, or stalling in the affected component.

• Provides a power boost at startup and helps stabilize voltage during operation
• Helps the connected component start promptly and operate smoothly under load
• Common failure signs include humming, slow or no start, or intermittent operation
• Contribute to overheating or a tripped breaker/fuse when the component tries to start

• Disconnect power at the breaker or unplug the appliance. Before handling, safely discharge the old capacitor using a proper resistor-rated tool.
• Photograph or note wire positions; move each lead to the same-labeled terminal on the new capacitor and ensure snug connections.
• Mount the capacitor securely in its bracket; keep terminals covered and clear of metal surfaces.

This controller kit is the appliance's main electronic control. It reads inputs from the user interface and sensors to power and coordinate key components. Replacing a failed controller restores responsive controls and consistent, reliable operation.

• Interprets commands from the keypad and sensors to manage operation
• Controls relays powering motors, fans, compressor, or valves as designed
• Coordinates modes and cycle timing for proper performance
• Common symptoms: dead or blank display, unresponsive buttons, won't start, intermittent shutdowns, or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board with ESD precautions; avoid touching connectors and components
• Photograph/label wire connections and transfer them one at a time to the new board
• After installation, verify any model-specific settings per the service documentation before testing

Refrigerator not cooling or compressor running hot? This start device kit includes relay and overload to restore proper compressor function. DIY install.

Refrigerator not cooling but running? This compressor start relay and overload kit fixes weak or failed start components. DIY repair in 20 minutes.

This kit includes the electrical components needed to start your refrigerator's compressor motor, including both the start relay and overload protector. These parts work together to provide the initial electrical boost needed to start the compressor and protect it from electrical overload. Replace this kit if your refrigerator isn't cooling, makes clicking noises, or if the compressor won't start.

Refrigerator clicking but not cooling? A failed compressor starter prevents reliable startup. This part restores proper cooling by helping the compressor start.

Refrigerator clicking but not cooling? A failed overload protector can prevent compressor startup. This part interrupts power during overheating.

This is a start relay device that attaches to the compressor and provides the initial electrical boost needed to start the compressor motor. It works in conjunction with the run capacitor to get the compressor running and then disengages once the motor reaches operating speed. Replace this device if the refrigerator is not cooling, the compressor clicks on and off repeatedly, or you hear a buzzing sound coming from the back of the unit.

Refrigerator won't cool or compressor clicks but won't start? This PTC start relay powers the compressor's start winding. Common DIY fix, restores cooling.

This is the start device (relay) that attaches to the compressor and provides the initial electrical boost needed to start the compressor motor. It plays a critical role in the refrigeration cycle by ensuring the compressor starts reliably. Replace this part if the compressor clicks on and off repeatedly, fails to start, or if the refrigerator is not cooling properly.