Kenmore / Sears Wall Oven Parts

• Door stuck closed

Turn off breaker, remove all screws { 4 on mine } inside oven door holding oven and microwave to kitchen cabinet and slide oven assembly out of cabinet {on to a temporary shelf of {4} 5 gallon buckets/plywood/bricks/shims that I made on the floor atop a scrap of carpet} just enough to access the side and rear screws of microwave's protective metal housing, then remove a total of 16 screws { there were 2 screws just inside top of "opened" microwave door that were holding top flat silver metal... Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

Slipped the old ones out, slid the new ones in. So simple, even my husband could do it! Read more

Replaced all ignitors. Read more

Pulled out the old one, popped in the new one 20 minutes. Fixed. Read more

Ordered new heating coils for stove Read more

• Little to no heat when broiling

I ordered a replacement broiler element from AppliancePartsPros.com. I watched the on-line video on how to replace the broil element: this was very informative! The repair went fine, except that the broil element connector wires both retreated into the back of the stove, as was warned in the video. We then removed the back of the stove, which was very easy, and the connections to the broil element were then very easy from the back. I would suggest that the on-line video be revised to... Read more

I had one element that would operate wide open when turned on the low setting. It needed the switch replaced. Since I was replacing other elements I went ahead replaced them all, adding new drip pans and wiring kits to each new element. Once I replaced everything I was still having issues with the element that had the switch replaced. After further investigation my AC voltage readings were not correct at this element. I traced the problem back to the Molex connector feeding voltage to the... Read more

Easy just pull clip and put back Read more

I purchased 2 new light rocker switches, Because the heating element rocker switch was unavailable. First I removed the power source for safety. Then I simply pulled each switch out individually with a flathead screwdriver for leverage. I simply unplugged the wires from the old rocker switch, discarded the old rocker, plugged the wires into the new rocker switch, and pushed the new switch appropriately back into the control panel. I used the same steps for both rocker switches. Once... Read more

• Element will not heat

Purchased a new Element surface and installed same... All Okay now... Read more

• Won't start

Bought this switch gas valve for the non-functional burner, and it cleared right up. Read more

With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more

Unfortunately when we bought our house 5 years ago, our custom, small drop-in range only came with one oven rack. I love to bake so it's been difficult! Because of the size and older model I assumed I would never find a part. Imagine my surprise when I found this website and they had it. Once it arrived and it fit, I about had a party!!!!! Read more

Replaced the control board and panel. Read more

I first tried to purchase the part directly from GE but they were not helpful at all. Remembering that I had purchased a transmission and other parts from appliance parts pros for my old Maytag washer before, I searched their easy-to-use parts catalog and there it was!!!! I asked for confirmation from Customer Service and after 2 says Research confirmed that it was the correct part. Replacing the element was quite simple following the very helpful diagrams on their website. Thank you so very... Read more