Kenmore / Sears Washer Gasket & Seal

I was able to find a great video on YouTube to replacing the video. This allows me to save money on a service call & perform the job myself. Read more

An online search for LG washing machine parts came up with a repair video from Appliance Parts Pros. I watched the video. It was very well done, very detailed, and took you step by step through the entire process to replace the tub bearings and the spider, from start to finish. After watching the video, I realized this repair was well within my abilities. No specialized tools were needed. I ordered the parts from Appliance Parts Pros, and all items were in stock and delivered within a couple... Read more

I ordered the dispenser and the distribution nozzle since the old one was in bad shape. I also replaced the boot since I had to take the entire machine apart and it is 20 years old. I watched your videos on you tune to learn what to do. I recently lost my job and really could not afford to hire someone to fix my washer. I have to say it wasn't that hard to do and my wife was so happy that I was able to fix it myself! I probably saved $200 or $300 in service calls and labor on top of what they... Read more

Turned out that the large gray boot/gasket had finally started to harden and deteriorate right at the bottom where the drain hose is. No surprise it leaked after seeing that. Installing the new gasket (and new clamps which I figured I would replace at the same time) did the trick. Fairly simple install. Do yourself a favor and buy the spring pliers to remove/install the clamps. Well worth the time and hassle they will save you. Read more

I replaced the door boot with a new one from AppliancePartsPros.com. The most difficult part was starting at the back end of the new boot onto the stationary rim, just in front of the tub. And then anchoring it in place with the existing spring from the previous boot. To start the boot I had to hook the top edge of the boot, where the arrow tab is, onto the rectangular projection on the tub rim and then roll the rubber boot edge down around the tub rim and hope the rim was going into the... Read more

First I watched the very, very helpful video (twice), then I planned out the job in regards to tools, work area, and access. I have stacked units of washer/dryer due to space restrictions and had to ask my son-in-law to help me lift the dryer of the washer once I had prepared the process by fabricating 2 pieces of 3/4" plywood to turn the dryer and then slide it out far enough were 2 people can lift it and then set it on some cribbing for easy handling. Disconnected the power, turned off the... Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more

Separated shell and replace oring. Replaced springs and shocks. Read more

Water was accumulating in the drawer pedestal, it was leaking from the front of the washer so I thought it was the front door seal. I also noticed it would leak even when the washer was not being used so I doubted it was the door seal. I googled the leak problems and watched a few videos which gave me confidence on washer disassembly. With the top panel off I noticed the leak coming from the water inlet assembly. Appliance Parts Pro’s had the part and replacement video and I replaced the part... Read more

I removed the drum, split it in half and replaced the bearings, seal and tub o-ring. Whirlpool did not offer the bearings without purchasing the back half of the tub for $350.00. I purchased a kit with a new seal for $75.00 and replaced them myself. Read more

Thank you for your video on web site , had no problem replacing clutch Read more

Replaced the coupler gasket. No leaks now. Read more

Replaced the felt seal and door vent assembly by removing the inside panel of the door and cleaning off the old seal and replacing with the new one. The vent assembly simply snapped out and was easy to replace with the new one. No more leaks and Mother was happy. Removal of the screws required a torx screw driver and someone to hold the door open while the panel was replaced. Easy fix. Read more