Kitchenaid Damper & Related

A duct kit designed to route a dryer's exhaust safely to the household vent system, restoring proper airflow and helping the dryer vent effectively when the original ducting is damaged or missing. What it does:

• Channels hot, lint-laden exhaust from the dryer to the exterior vent to reduce indoor heat and moisture.
• Replaces crushed, torn or disconnected ducting that can cause poor drying performance.
• Use when you notice longer dry times, excess heat or lint buildup near the dryer, or backdrafting from the vent.
• Helps maintain proper vent airflow when installed and secured per manufacturer and local code requirements.

• Disconnect electrical power (and gas supply for gas dryers) before installing or servicing venting components.
• Follow the appliance manufacturer's installation instructions and local building/venting codes for diameter, length and material.
• Avoid crushing, kinking or sharp bends in the duct; secure joints with approved clamps or foil tape and check for leaks.

This upper vent cover replaces the visible duct cover on a range hood to restore proper appearance and help channel exhaust air. It provides a finished look and protects ductwork from grease and debris. What it does:

• Covers the vent duct above the hood for a clean, finished appearance
• Helps direct exhaust up into the duct while protecting internal components from dust and grease
• Use when the original chimney is dented, cracked, or cosmetically damaged
• Reduces visible gaps between the hood and ceiling when properly installed

• Designed to mount to the hood body or chimney assembly; follow OEM mounting points
• May require removal of the hood's grease filters or upper panel for access
• Ensure power is off to the appliance before starting work to avoid electrical hazards
• Replace damaged ducting or fasteners as needed for a secure fit

This damper heater is the heater element used with the refrigerator air-damper assembly to help prevent frost and condensation buildup around the damper. Replaces a failed heater to restore proper damper operation and airflow. What it does:

• Warms the damper area to reduce ice and condensation that can block the damper
• Helps ensure the fresh-food and freezer compartments share airflow as intended
• Commonly replaced when frost or ice accumulates near the damper or when the damper fails to open/close smoothly
• Works as part of the damper/air control system; does not include the full damper housing or actuators unless specified

• Disconnect power to the appliance before replacing this part to avoid shock or injury
• Access may require removing interior panels or the damper housing; follow OEM instructions for your model
• Inspect the damper housing and actuator for damage or ice buildup when replacing the heater

This replacement exhaust vent directs oven/dryer exhaust airflow away from the appliance to maintain proper ventilation and reduce backflow. Restores intended airflow path to help reduce odors and heat buildup around the appliance. What it does

• Channels exhaust fumes and hot air out of the appliance's vent path.
• Helps restore proper ventilation when previous vent is cracked, warped, or blocked.
• Can reduce abnormal heat, odors, or poor drying/cooking performance tied to ventilation issues.
• Limits airflow leak points that can cause noise or vibration during operation.

• One exhaust vent housing.

• Disconnect power (and gas, if applicable) before starting work.
• Inspect and replace any worn gaskets, clamps, or vent hose to ensure a proper seal.

This oven vent directs hot air out of the oven cavity and helps maintain proper internal temperature and airflow. It replaces a damaged or warped vent to restore venting performance and oven appearance. What it does:

• Channels heat and steam out of the oven cavity to support even cooking
• Helps prevent heat buildup behind the oven and adjacent cabinetry
• Replaces cracked, bent or discolored vent trim that can affect airflow or appearance
• Compatible with factory vent locations — installs where the original vent was mounted

• Designed for rear/top vent mounting; verify orientation matches your appliance before installing
• Disconnect power to the appliance before beginning any service to avoid shock or injury
• Handle edges carefully; use appropriate tools to remove mounting screws and clips
• If vent damage is extensive or other components are affected, inspect surrounding parts and wiring

This duct cover extension kit raises a range hood's chimney to fit taller ceilings and gives a finished look where the standard chimney is too short. It provides an easy way to extend the visible duct cover for a cleaner installation. What it does:

• Extends the hood chimney/duct cover to reach higher ceilings
• Covers exposed ductwork for a finished appearance
• Helps align the duct cover with cabinetry and ceiling lines
• Useful when replacing or modifying hood installation height

• Turn off power to the hood before beginning any work
• Follow the manufacturer's instructions and use proper fasteners for your wall/ceiling type
• Do not alter structural supports or ventilation openings; consult local codes

This air deflector redirects airflow inside the appliance to help channel heated or cooled air where it's needed for proper operation. It's a simple replacement that restores intended air pathing and performance. What it does:

• Directs internal airflow to improve circulation and temperature consistency
• Prevents air from blowing directly on sensitive components
• Helps reduce uneven cooking/cooling symptoms and localized hot or cold spots
• Can eliminate abnormal airflow noise caused by misdirected vents

• One air deflector

• Disconnect power (and gas if applicable) before servicing
• Access may require removing exterior or interior panels; keep track of screws and fasteners
• Replace with the correct orientation so air passages align with vents

This replacement chimney is the exterior cover that hides the hood's ductwork and mounting hardware, restoring the finished look of your kitchen range hood and protecting internal components from grease and dust. Fits the upper section of select chimney-style hoods. What it does:

• Covers and protects ductwork and mounting brackets for a clean, finished appearance
• Helps prevent grease and dust from settling on internal hood components
• Replaces damaged, dented, or missing chimney pieces that affect appearance or fit
• Restores proper alignment of the hood's upper housing for secure installation

• One chimney upper cover

• High-level replacement — basic hand tools typically required; lift and support the chimney during installation
• Consider a second person for safe handling and alignment of the cover
• Turn off power to the hood before removing or working near electrical components