Kitchenaid Dispenser Parts

This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:

• Actuates the ice chute door during dispensing and returns it closed for a proper seal
• Helps reduce frost, condensation, and ice clumping around the dispenser
• Can address ice not dispensing due to the door not opening/closing
• May resolve clicking or grinding noises from the dispenser area

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove dispenser trim/control panel to access the ice door assembly; handle wiring carefully
• Note linkage and wire orientation before removal to ensure proper reassembly
• After installation, test the dispenser to verify the door opens/closes and seals the chute

This lighted dispenser actuator pad assembly replaces the extra-large paddle you press to dispense water or ice from the door. It restores smooth, reliable activation and visibility when the original pad is cracked, worn, or unresponsive.

• Acts as the user-pressed paddle that engages the dispenser switch for water/ice
• Integrated illumination helps light the dispenser alcove for easier use in low light
• Helps address intermittent dispensing, sticking or continuous dispensing, or the need to press excessively hard
• Replaces broken, loose, or discolored paddles for better function and appearance

• Disconnect power before servicing the dispenser area
• Remove the drip tray and dispenser trim/escutcheon to access the pad assembly
• Release retaining tabs/screws and disconnect any wire harnesses; note orientation
• Install the new assembly, reconnect wiring, reassemble trim, restore power, and test dispensing and lighting

This bi-metal is the thermal actuator that releases the detergent dispenser at the proper point in the wash cycle. Replacing a weak or failed actuator restores reliable detergent cup opening and consistent detergent delivery for better cleaning. What it does:

• Heats and flexes when energized by the control to trip the dispenser latch
• If failed, the detergent cup may not open or may open inconsistently
• Can leave detergent in the cup and lead to poor cleaning results
• Often suspected when the cycle runs but the soap door stays closed

• 1 bi-metal actuator assembly

• Disconnect power at the breaker before servicing
• Remove the inner door panel to access the dispenser area
• Note wiring positions and orientation; transfer connectors securely to the new actuator
• The dispenser latch/linkage moves freely and test door release before reassembly

This drip tray sits beneath the grate area to catch grease and boil-overs, helping keep the cooktop cleaner and protecting components below. Replacing a bent, corroded, or missing tray restores proper fit and appearance. What it does:

• Collects drips, grease, and spills under the grate area
• Helps prevent liquids from reaching the burner box or wiring
• Supports correct placement of the grate/grill assembly
• Common symptoms: missing tray, heavy rust, warping, leaks or messes under the top

• 1 drip tray

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove the cooking grates/grill section to access the tray
• Lift out the old tray and position the new one with correct orientation
• Reinstall grates and verify proper seating and clearances before use

This replacement housing restores the appliance's structural enclosure, protecting internal components and helping panels and controls align properly. Use it to replace cracked, warped or damaged housings so the unit fits and functions as intended. What it does:

• Provides the main structural enclosure and mounting surface for internal components and exterior panels
• Replaces cracked, dented or broken housings that can allow misalignment or rubbing of parts
• Helps reduce vibration and movement by restoring proper fit between panels and internal assemblies
• Keeps internal components shielded from debris and wear that can lead to downstream issues

• Disconnect power (and water, if applicable) before starting any repair
• Handle edges carefully; housing edges and sheet metal can be sharp
• Basic hand tools are typically required; follow the appliance service manual for disassembly/reassembly steps

This dispenser facade replaces the outer trim pieces around your refrigerator's ice and water dispenser, restoring appearance and proper fit for smooth operation and sealing. It's a direct-fit cosmetic and protective assembly. What it does:

• Covers and protects the dispenser opening and controls from damage and debris
• Provides a finished look and helps direct water/ice into the cup
• Restores proper alignment when cracked, warped, or broken facade causes interference
• Helps prevent drafts and minor water splash at the dispenser area

• Disconnect power and shut off water to the appliance before servicing
• Many installations require removing the dispenser bezel and releasing snap-clips or screws; save hardware for reinstallation
• Handle plastic trim carefully to avoid scratches; use a soft pad when setting parts down

The Thermostat Housing is an OEM part for Whirlpool dishwashers. It encases the thermostat responsible for accurately monitoring water temperatures throughout cleaning cycles. 

Symptoms of a faulty housing include:

• Inconsistent or improper water heating  
• Delayed or incomplete cycles from temperature control issues
• Error codes or failure detection by the control board

Causes may involve cracks allowing steam penetration, loose mounting points compromising seals, or damaged seals leaking interior thermostat components. 

This OEM replacement fits Whirlpool, KitchenAid, Jenn-Air, and some Kenmore models as well.

The Dispenser Drip Tray is an OEM part for Whirlpool refrigerators featuring built-in water dispensers. Located underneath the outlet spout, it collects any accidental water overflow or spilled cubes to prevent messes. 

Causes of a bad dispenser drip tray involve cracks interfering with its collection surface, or warping preventing it from fully guiding water into the pan below. Damage risks difficulties. 

Symptoms include:

• Water collecting outside the tray area on the cabinetry below
• Dispenser outlet jams from backflow during partial fills  
• Ice cube spills create a slipping hazard on the floor
• Increased effort required to avoid messes during dispensing

This OEM Whirlpool part is also compatible with some GE, Kenmore, and LG refrigerator models.

The Icemaker Fill Cup is an OEM part for Whirlpool bottom-mount and side-by-side refrigerators. Located inside the icemaker assembly, the fill cup sensor works to automatically detect when an ice scoop or bucket is in place below the icemaker chute. It signals the icemaker to drop ice cubes into the receptacle below.

Causes of a bad fill cup sensor can include mineral or dirt build-up inhibiting sensor response, moisture damage to its electronic functioning, or physical damage to the sensor head.

Symptoms of a bad fill cup sensor include:

• Ice failing to dispense or drop when a container is in place
• Ice clumping in the chute instead of dispensing properly  
• The icemaker continuing to run even with ice present below
• Inability to sense when ice is removed from the bucket

This OEM Whirlpool replacement fill cup sensor is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore bottom-mount and side-by-side refrigerators. 

The Detergent Dispenser Assembly is an OEM part for Whirlpool dishwashers, designed to store and release detergent and rinse aid at the appropriate times during the wash cycle. This component ensures that your dishes are cleaned efficiently by dispensing the correct amount of detergent for optimal washing performance. 

Causes of a malfunctioning dispenser can include mechanical failure of the latch or spring mechanism, clogging due to detergent buildup, or electrical issues preventing the dispenser from operating correctly.

Symptoms of a bad Detergent Dispenser Assembly include:

• Detergent not being dispensed correctly, leading to poorly cleaned dishes.
• The dispenser door not opening during the cycle or failing to latch properly before starting.
• Leakage of detergent from the dispenser, indicating a seal failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement cap protects and seals a small appliance component to prevent debris entry and reduce wear. It restores the original fit and helps keep moving parts and seals working as intended. What it does:

• Covers and protects an exposed component or fitting to prevent dirt and moisture intrusion
• Maintains proper spacing and alignment for nearby parts
• Helps reduce rattling or contact noise from loose or worn ends
• Can prevent premature wear or minor leaks when used as intended

• Disconnect power and water before servicing the appliance
• Access the cap location by removing the adjacent panel or trim
• Press or snap the cap into place; use gentle, even pressure to avoid damage
• If the cap secures a sealed connection or seal, inspect nearby gaskets and replace if damaged