Need Help?
Call or text
The Dispenser Grille is an OEM part for Whirlpool refrigerators. This grille is located at the base of the refrigerator's water and ice dispenser, collecting drips and spills to keep the dispenser area clean and dry.
Causes of a bad dispenser grille can include regular use, accidental impacts, or exposure to harsh cleaning chemicals.
Symptoms of a bad dispenser grille include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Ordered part, it fit perfectly! Read more
Replaces cracked, broken, or discolored water dispenser lever on side-by-side refrigerators. Installs behind dispenser faceplate. White finish.
I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better. I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some... Read more
Catches drips and splashes beneath your refrigerator's ice and water dispenser. Replace if cracked, broken, or missing to keep the door area clean.
All parts arrived in a timely matter, all parts fit as expected, easy fix Read more
Replacement actuator pad for refrigerator water and ice dispensers. Snaps into dispenser panel. Replace if cracked, broken, or tabs are damaged.
Super easy fix, remove two screws behind drop tray, unplug the wiring harness to dispenser, unplug and remove old pad, then snap new one into place. Reconnect harness. Took less than 5 minutes, works like new. Read more
Soap dispenser door won't latch or detergent stays in compartment? This dishwasher dispenser assembly releases detergent at the right time. Moderate DIY.
My husband Ron diagnosed the problem, that a new Soap dispenser assembly was needed. We ordered the part, and it arrived in 48 hours. The front dishwasher door was rusty, but my husband managed to dis-assemble and replace the dispenser. Pleased with purchase process. Part fit fine. Janie Read more
Color: black. Measures about 9 inches wide by 2-1/2 inches deep.
Ordered the parts. Watched a great video on this web site. Installed. Fixed. Easy peesey. Read more
Replaces a cracked, worn, or unresponsive dispenser pad on your refrigerator door. Installs in the front dispenser housing for water and ice.
Removed water catcher, then 4 screws in water/ice vault in door, then removed screws on door side (5) top (2) and bottom (2). Removed stainless door skin. Removed 4 hex head bolts in ice/water vault (containing pads) and 4 bolts on the module immediately above the vault. Pulled the vault and module above out part way to unplug one cable. Then laid on table to unplug pads. From back, each pad has a small indent preventing the pad from being pushed up and removed. Push the small indent with a... Read more
Connects the dispenser motor to the ice bucket auger. Replace if stripped, worn, or broken to restore proper torque transfer and smooth ice dispensing.
Removed drip pan from ice dispenser. Removed two screws hidden behind drip pan to loosen bezel at bottom. Carefully lifted bezel off top hook to expose controller board cabling. Disconnected three connectors to control board behind bezel to remove bezel completely. Removed two (possibly three) screws to access the back of the ice chute mechanism. Removed broken paddle that just snaps in, being careful to capture paddle spring. Put paddle spring on new paddle and maneuvered spring-end... Read more
This ice dispenser solenoid assembly engages the dispenser mechanism to switch between crushed and cubed ice. A worn or failed solenoid can prevent the selector from changing modes or stop ice from dispensing smoothly.
Forms the interior of your refrigerator's ice and water dispensing area. Replace if cracked, broken, or causing drips and frost buildup at the chute.
I bought the complete ice chute. It was easy to install and it works perfectly now. Many thanks. Read more
Color: black. It measures about 9 inches wide by 4-1/2 inches deep.
Ordered the parts and simply fit them in place. Read more
Color: black. Measures about 10 inches wide by 4 inches deep.
I replaced the water inlet valve & both dispenser levers (water & ice) and adjusted the lever locking spring. Read more
Channels ice from maker to dispenser opening. Replace if cracked, broken, or missing to prevent ice scatter and jams. Installs in freezer door dispenser.
Identified and ordered part Read more
Ice maker not filling properly or water leaking in freezer? A cracked fill cup causes inconsistent fills and leaks. Simple DIY fix guides water correctly.
I SAW THE VIDEO AND WAS SO EASY THAT MY CHILDREN COULD DO IT Read more
Replaces the lighted paddle you press to dispense water or ice from your refrigerator door. Restores activation when the original pad is cracked, worn, or missing.
Replace the part and working good. Read more
This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:
I replaced the ice door motor with new hardware, circuit board on touch panel display then the main ECB on top in the doghouse. It finally came to life and started working! No issues with the front panel and everything works as it did! Read more