Need Help?
Call or text
Guides ice from the bucket through the dispenser chute. Replace if cracked, broken, or missing to prevent ice jams and ensure smooth dispensing.
Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more
Replaces a cracked, broken, or worn ice dispenser chute door on your refrigerator. Installs in the freezer door ice dispenser to control ice flow.
The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more
Catches spills from water and ice dispenser. Replace if stained, cracked, or broken. Installs in front dispenser area. Snaps in without tools.
Finding the part was puzzling. AppliancePros had the relevant manufacturer's part schematics handy on-line through which I quickly identified and order the replacement part. But the best aspect was AppliancePros' Amazon-like excellence in a) pricing and b) swift delivery (with precious tracking included). Read more
Replacement dispenser actuator pads for refrigerator ice and water controls. Installs on dispenser housing. Replace if cracked, broken, or worn.
Replaced the actuator pad on the Whirlpool Gold Series, releasing the electronic menu pad to get to the water activator pad was the biggest hurdle. The release tabs are underneath the menu pad and you may feel as if you may break them when releasing them. They did not break but I did hold by breath. Read more
Refrigerator dispenser pad installs on the control panel for water and ice operation. Replace if cracked, unresponsive, or causing erratic dispensing.
Order part and replaced switch. Read more
Grille sits below the water and ice dispenser on your refrigerator door to catch spills. Replace if cracked, stained, or damaged. Snaps into place.
Once the parts arrived, I followed the help video that was emailed to me with my order confirmation step by step. Super useful! The video quality and editing were well done and the instructions were very specific. I felt like a pro! Read more
Plastic grille that sits at the base of your refrigerator's water and ice dispenser to catch drips and spills. Replace if cracked, broken, or missing.
Ordered part, it fit perfectly! Read more
Replaces cracked, broken, or discolored water dispenser lever on side-by-side refrigerators. Installs behind dispenser faceplate. White finish.
I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better. I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some... Read more
Replacement actuator pad for refrigerator water and ice dispensers. Snaps into dispenser panel. Replace if cracked, broken, or tabs are damaged.
Super easy fix, remove two screws behind drop tray, unplug the wiring harness to dispenser, unplug and remove old pad, then snap new one into place. Reconnect harness. Took less than 5 minutes, works like new. Read more
Replacement drip tray for refrigerator water and ice dispenser. Installs below dispenser opening. Replace if cracked, warped, discolored, or missing.
After using the crushed ice feature on my KitchenAid French Door refrigerator, the ice maker wouldn't stop dispensing ice, crushed or cubed. I thought it had to do with the paddle switch being stuck or something else in the door, but all door components seemed to be working as intended. I ended up pulling the ice maker out and disconnecting the wires to the auger so that I could leave the refrigerator plugged in. I call AppliancePartsPros.com the following morning and explained my situation.... Read more
Catches drips and splashes beneath your refrigerator's ice and water dispenser. Replace if cracked, broken, or missing to keep the door area clean.
All parts arrived in a timely matter, all parts fit as expected, easy fix Read more
Replaces a cracked, worn, or unresponsive dispenser pad on your refrigerator door. Installs in the front dispenser housing for water and ice.
Removed water catcher, then 4 screws in water/ice vault in door, then removed screws on door side (5) top (2) and bottom (2). Removed stainless door skin. Removed 4 hex head bolts in ice/water vault (containing pads) and 4 bolts on the module immediately above the vault. Pulled the vault and module above out part way to unplug one cable. Then laid on table to unplug pads. From back, each pad has a small indent preventing the pad from being pushed up and removed. Push the small indent with a... Read more
Black plastic grille that catches water overflow below the dispenser on side-by-side refrigerators. Replaces cracked, stained, or missing grilles.
Ordered the parts. Watched a great video on this web site. Installed. Fixed. Easy peesey. Read more
Connects the dispenser motor to the ice bucket auger. Replace if stripped, worn, or broken to restore proper torque transfer and smooth ice dispensing.
Removed drip pan from ice dispenser. Removed two screws hidden behind drip pan to loosen bezel at bottom. Carefully lifted bezel off top hook to expose controller board cabling. Disconnected three connectors to control board behind bezel to remove bezel completely. Removed two (possibly three) screws to access the back of the ice chute mechanism. Removed broken paddle that just snaps in, being careful to capture paddle spring. Put paddle spring on new paddle and maneuvered spring-end... Read more
Controls ice type selection between cubed and crushed ice in your dispenser. Replace if the selector won't switch modes or if the assembly is damaged.
Black overflow grille for refrigerator ice/water dispenser area. Replaces cracked, stained, or missing grilles. Measures 9" wide by 4.5" deep. Snaps in.
Ordered the parts and simply fit them in place. Read more