Kitchenaid Refrigerator Parts

I searched online for replacement parts and Appliance Parts Pros had the part in stock. Before I ordered the part, I watched the video to see if I could handle the repair. I ordered the part and soaked the gaskets with warm water in the tub. The old gaskets had a much simpler setup, so no cutting was involved. I simply pulled the old gasket out of the track without issues, and installed the new one with finger pressure. Per the video, I took both doors off. However, due to the design, I could... Read more

The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more

Replaced the damper control. It took only 10-15 minutes. Since replacement, the clicking noise has stopped. Very happy with the result. However, want to share that there was probably nothing wrong with the original damper other than the original faulty design. The flap opens and closes and believe the clicking noise was the result of plastic against plastic. Noticed the new damper control is exactly the same as the original except that one of the flap sides now has a thick piece of rubbery... Read more

Re placed the water inlet valve. Read more

• Won't start
• Fridge too warm
• Freezer section too warm

Replaced capacitor and starting relay on the compressor in 15 minutes. The problem may have just been the capacitor, but rather than trying that and if it didn't solve the problem i would have had wait for the relay. Read more

We first emptied out the freezer to another freezer, turned off the refrigerator, and let it defrost. We ordered a freezer door gasket from Appliance Parts and it arrived within a few days. We watched the video on how to replace it, followed the directions, and the gasket was successfully replaced. However, while the freezer was off, I cleaned the inside. Unfortunately, we turned it on before it completely dried and the water in the tracks caused the drawers to stick. Now we have turned... Read more

Replaced water valve and ice maker Read more

• Light not working

We had delayed repairing the problem because we received a price of more than $ 100 from a local appliance repairman. However, after viewing the view on the ApplianceParts Pro website, I saw what an easy repair it would be. After receiving the part from you, I had my son do the repair because I felt it would a good father - son bonding time. It was so easy and he was proud of his ability. Thanks for your excellent repair video and the excellent price. It costs less than $ 22 instead of more... Read more

Finding the part was puzzling. AppliancePros had the relevant manufacturer's part schematics handy on-line through which I quickly identified and order the replacement part. But the best aspect was AppliancePros' Amazon-like excellence in a) pricing and b) swift delivery (with precious tracking included). Read more

• Door won't open or close
• Door sweating
• Frost buildup
• Leaking

I followed a video to remove the inside door panel and gasket. Putting the new gasket was as easy as the video said. The only problem was ice had built up on the inside of the door panel that needed to be defrosted. Read more

I first thought it was the auger in the ice container so I changed it and it was not the problem. I then talked to ApplianceParts customer service that it might be the yoke on the motor that turned the auger or even the motor itself even though it worked. I ordered the parts, the yoke was supposed to be able to be changed by itself but mind would not come off the motor shaft so I had to cut it off just to remove it from the unit so I had to change the motor anyway because of this. So I advise... Read more

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more

First, I watched your VERY HELPFUL videos showing exactly how to remove and assemble the parts. I removed the salvageable parts from the old shelf frame and reassembled it. Read more

Used U-Tube diagnostic clips to diagnose that most likely problem was a worn Evaporator Fan Motor which is located in the freezer back wall, located in the top third of the unit. I removed 6 hex head screws from the freezer's interior back panel that covers the evaporator coils. The cover is located in the lower 2/3s of the back wall. Removed all shelving. Also removed screws that held in shelf supports on one side of the freezer wall. I then removed the back panel. You may need to... Read more

So this is a poor design in the first case. Not having a center support in the back almost guarantees a failure there eventually. I kludged together a support in my original more than a year ago, but finally the part broke too bad to limp along with anymore. This is the part I needed. That being said, be very attentive about the fact that it's not the entire shelf assembly. There is a metal support across the front of the frame that is not included. The trim above the drawers, and the... Read more

I located the web site via the internet and contacted the 1-800 number. The service rep was incredibly helpful and personable. After providing her with the model number and parts needed,the process could not have been easier. My replacement parts arrived the next day a perfect match. I highly recommend using this service, first class all the way. Read more