Maytag Auger, Helix, Crusher

This ice enclosure is the molded housing that surrounds the icemaker inside the freezer, helping position the assembly and guide airflow for reliable ice production. Replace a cracked or missing cover to restore proper fit and protection around the icemaker.

• Mounts around the freezer icemaker to shield and correctly position the assembly
• Helps direct airflow for consistent ice formation and harvest
• Reduces frost intrusion in the icemaker area
• Common fix for cracked, warped, loose, or missing housing

• Disconnect power and turn off the water supply before service
• Remove the ice bin and icemaker as needed to access the enclosure
• Transfer any clips/brackets from the old part and reuse existing hardware
• Verify icemaker alignment and fill tube clearance before restoring power

This replacement ice maker cover snaps over the icemaker assembly to shield moving parts and keep frost and debris out. Replacing a cracked or missing cover helps restore reliable ice production and a clean, finished look inside the freezer.

• Protects the ice maker's internal components from accidental contact and debris
• Helps reduce frost buildup around the ejector and motor area
• Maintains proper fit and clearance for smooth ice harvesting
• Common symptoms: cover cracked, broken tabs, loose or missing cover, excess frost around the icemaker

• Disconnect power to the refrigerator and turn off the water supply
• Remove the ice bin to access the ice maker
• Release any retaining tabs or screws and remove the old cover
• Install the new cover, ensuring the ejector and shutoff arm move freely; restore power and water

This ice maker cover fits over the ice maker head to protect the control module and moving parts inside your freezer. Replacing a cracked or missing cover helps prevent frost intrusion and restores a clean, finished look.

• Shields the ice maker mechanism from debris and moisture
• Helps maintain airflow to reduce frost at the ice maker face
• Replaces a cracked, warped, or missing cover with broken tabs
• Can help address exposed gears/wiring or rattling from a loose cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the front of the ice maker
• Release retaining tabs or screws and remove the old cover
• Align and snap the new cover fully into place; verify it's secure and clear of moving parts

This icemaker fill cup guides incoming water from the refrigerator's inlet tube into the ice mold, helping prevent splashing and freeze-ups during the fill cycle. Replacing a cracked or missing cup restores consistent fills and reduces leaks.

• Directs water from the fill tube straight into the icemaker mold
• Helps prevent overspray, splashing, and ice buildup around the icemaker
• Replace if the cup is cracked, warped, loose, or missing
• Common symptoms: water dripping/freezing under the icemaker, clumped or misshapen cubes

• Unplug the refrigerator and turn off the water supply before servicing
• Remove the icemaker assembly as needed to access the inlet/fill area
• Release the old cup and seat the new cup so the fill tube aligns with the opening
• Restore water and power; check for proper fill and any leaks

This ice storage bin holds the ice made by your refrigerator's icemaker and keeps it contained and easy to access in the freezer. Replace a cracked or warped bin to prevent spills, jams, and poor seating.

• Collects and stores ice cubes produced by the icemaker
• Keeps cubes contained to minimize spills and stray frost
• Slides/seats on the designated rails or shelf area in the freezer
• Common signs of failure: cracks, broken tabs, bin won't seat or slides out, ice falling into the freezer

• Unplug the refrigerator or disconnect power; switch the icemaker off
• Pull the old bin straight out; empty and clean the area
• Slide the new bin in until fully seated; restore power and turn the icemaker back on

This replacement ice auger fits inside the freezer ice bin and rotates to move ice to the dispenser and through the crusher, restoring consistent cubed or crushed ice dispensing when the original auger is bent, stripped, or broken.

• Moves ice through the bin to the dispenser chute
• Works with the crusher blades/selector for crushed or cubed dispensing
• Common symptoms: no ice dispensed, motor runs but ice doesn't move, slow or jammed dispensing, grinding noises from the bin
• Replaces a bent, worn, or broken auger spiral that fails to engage or feed ice

• Disconnect power; remove the ice bin from the freezer/door
• Empty the bin; carefully disassemble the crusher blade stack, noting the exact order of blades, spacers, and washers (take reference photos)
• Transfer components onto the new auger and secure the retaining hardware; verify smooth rotation before reinstalling
• Wear cut-resistant gloves—crusher blades and edges are sharp

This comb-shaped insert mounts at the front of the modular ice maker. It strips freshly ejected cubes from the rake and directs them into the bin to help prevent jams and cube hang-ups for consistent ice harvests.

• Guides cubes off the ejector fingers and into the bin
• Helps prevent cubes from re-entering the mold, bridging, or jamming
• Replaces a cracked, warped, or missing stripper to restore proper harvest path
• Typical symptoms: cubes stuck on the ejector, repeated jams, ice spilling or clumping

• Disconnect power to the refrigerator and turn off the ice maker before servicing
• Remove the ice maker front cover; release locking tabs or screws to remove the old stripper
• Position the new stripper over the ejector fingers; seat fully without forcing the rake
• Reinstall cover/ice maker, restore power, and allow a full cycle to verify operation

This refrigerator ice auger sits inside the ice bin and rotates to move cubes or crushed ice toward the chute. Replacing a worn, bent, or stripped auger restores smooth, consistent dispensing performance. What it does:

• Rotates inside the ice bin to feed ice toward the crusher and dispenser chute
• Helps deliver either cubes or crushed ice depending on the selector
• Common symptoms: dispenser motor runs but no ice comes out, weak/intermittent dispensing, frequent ice jams, or grinding noises from the ice bucket

• 1 ice auger

• Unplug the refrigerator before servicing; remove and empty the ice bin
• Note the order of internal parts during disassembly; transfer any reusable hardware from the original assembly
• Wear cut-resistant gloves—metal and plastic edges can be sharp
• Reassemble so the auger turns freely by hand, reinstall the bin, restore power, and test the dispenser

This small plastic control arm extension links to the mechanism it serves, restoring proper movement and engagement so the appliance can operate as intended. It's a simple, direct-replacement component designed to snap in and align correctly.

• Connects to the existing control arm to extend its reach and function
• Helps correct issues like improper engagement or intermittent operation
• Can address symptoms such as sticking, misalignment, or failure to activate
• Sized to fit the original mounting points for consistent motion

• Disconnect power (and water if applicable) before servicing
• Note the orientation of the original part to match during reassembly
• Inspect the mating control arm and linkage for wear or damage
• Test operation before fully reassembling panels or covers

This ice deflector guides ice cubes from the icemaker into the ice bin to help keep ice delivery consistent and reduce cube jams or spills. It's a simple replacement that restores proper ice routing in compatible refrigerators. What it does:

• Directs ice cubes from the icemaker into the ice bin for orderly dispensing
• Helps prevent ice clumping and blockages that can stop ice flow
• Keeps ice moving away from the icemaker assembly and into the bin
• Restores proper alignment and function after a cracked or missing deflector

• Disconnect power to the refrigerator before servicing to avoid electrical or mechanical injury
• Remove the ice bin or access panel per your model's service instructions to reach the deflector
• Part typically snaps or slides into place; reuse existing fasteners unless new hardware is supplied
• After installation, reconnect power and run the icemaker through a cycle; discard any ice made during the repair if contamination is suspected

The Ice Maker Scoop is an OEM component specifically designed for Whirlpool ice machines. As an included accessory, it provides a sanitary and convenient way for users to fetch ice from the storage bin.

The scoop is strategically designed with an ergonomic handle and wide opening bowl shape. This facilitates easy scooping and transport of ice cubes without spillage or crumbling. Its food-safe materials maintain hygienic conditions in the storage area. 

Symptoms of a faulty scoop include:

• Cracks or breaks that compromise the scooping surface 
• Leaks or spills of ice when trying to scoop
• Sharp edges that risk cuts or scratches
• Warping or loosening of the handle attachment over time

This OEM Whirlpool scoop is also compatible with some Scotsman and Manitowoc ice machines. Replace yours today to restore safe and hygienic ice retrieval from the storage bin.
 

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

This replacement ice bin stores the ice produced by your refrigerator's icemaker and fits into its designated compartment for easy access. Replace a cracked or warped container to restore reliable ice storage and smooth dispensing.

• Holds harvested ice until use
• Guides cubes toward the dispenser outlet
• Restores proper fit when the original bin is cracked, broken, or warped
• Common symptoms: ice won't dispense or jams; ice spills into the freezer; bin won't seat or latch properly

• Unplug the refrigerator or disconnect power before servicing
• Empty and remove the old bin from the compartment
• Align and slide the new bin into position until fully seated
• Restore power and allow time for new ice to accumulate

This ice enclosure is the molded housing for the refrigerator's ice path. It supports and aligns related components so ice moves properly and helps keep warm air out to reduce frost and moisture around the ice area.

• Provides a rigid mounting point for ice-path components to keep alignment and flow
• Helps maintain an air barrier to minimize frost, sweating, and ice clumping
• Replace if the original housing is cracked, warped, or broken
• Common symptoms include frost or condensation near the ice opening, ice clumps, or poor/jammed ice dispensing

• Disconnect power and shut off water before servicing
• Access the ice area (door or interior access varies by model); retain screws and clips for re-use
• Transfer any guides, seals, or switches from the original enclosure to the new part in the same orientation
• Reassemble, restore power, and check for smooth operation and a good seal

This coupling is the small connector that links a drive motor to its mating component, transferring rotation so the appliance operates smoothly. Replacing a cracked or stripped coupling restores reliable drive and helps prevent further wear.

• Connects the motor shaft to the driven part to transmit torque
• Maintains alignment to reduce wobble and slippage
• Failure signs can include no movement, intermittent operation, clicking/grinding, or visible cracks/rounding
• Restores consistent motion of the connected part once replaced

• Disconnect power (and shut off water/gas if applicable) before servicing
• Access the drive area and remove any covers/tray/drive components as needed
• Pull the old coupling straight off the keyed or D-shaped shaft; clean and inspect the shaft
• Align and press the new coupling fully onto the shaft, reassemble, and test

This replacement ice bucket and crusher assembly stores ice and drives it to the dispenser. Its built-in auger and crusher help maintain smooth cube or crushed dispensing when the original bucket is cracked, jammed, or worn. What it does:

• Holds ice and feeds it to the dispenser chute
• Crusher mechanism breaks up cubes for the Crushed setting
• Helps resolve no or slow ice dispensing, only cubes dispensing, or grinding noises
• Replaces cracked, warped, or stripped ice buckets

• 1 ice bucket and crusher assembly

• Unplug the refrigerator and turn the ice maker off before servicing
• Lift out the old bin carefully; discard loose ice to avoid spills
• Align the drive coupling with the auger, then slide the new bin in until fully seated
• Restore power, turn the ice maker back on, and test both Cube and Crush functions