Maytag Touch Pad

Color: Black.

This backguard panel replaces the vertical rear trim on a range, restoring appearance and protecting the control area from spills and heat. It returns the unit to factory look and helps keep controls cleaner. What it does:

• Covers the rear control area and conceals wiring and mounting points
• Protects controls and electronics from splashes, grease, and heat
• Restores the stove or range's original finished appearance
• Helps prevent debris from entering openings behind the control assembly

• Remove power to the appliance before beginning work; confirm power is off at the breaker
• Typical install requires removing fasteners and lifting the old backguard off anchor points
• Handle edges carefully — replacement panels can have sharp edges
• If mounting hardware or clips are damaged, replace them with OEM parts for secure fit

This control panel is the user interface assembly that houses the buttons and display for operating your range or oven, restoring full control and reliable command feedback for cooking functions and settings. What it does:

• Replaces the front user interface so buttons, touchpads, or display respond correctly.
• Restores control of cooking modes, temperature settings, timers, and oven controls.
• Helps resolve unresponsive or intermittently working buttons, blank or flickering displays, and incorrect control behavior.
• Works as the main interface between the user and the appliance's control electronics.

• 1 control panel assembly

• Disconnect power at the house circuit breaker before beginning any work to avoid shock.
• Handle the display and ribbon connectors carefully; avoid bending or stressing circuit traces.
• Confirm cabinet and trim removal steps for your specific appliance model before installation.

This replacement cover is a protective panel that helps shield internal components from dust and debris and restores the appliance's finished appearance. Installing the correct cover keeps parts protected and helps maintain safe, reliable operation. What it does:

• Protects internal electronics and wiring from dust, lint, and incidental contact
• Restores the appliance's exterior finish where the original cover was damaged or removed
• Helps prevent accidental access to moving or energized components
• Can reduce noise by covering openings near motors or fans

• One replacement cover

• Disconnect power to the appliance before beginning any work
• Handle edges carefully to avoid cuts and to prevent damage to the cover finish
• Verify orientation and fastener locations before tightening screws; do not overtighten

This control panel is the oven/range user interface that lets you set cooking modes, temperature and timers while showing status information. Replacing a faulty panel restores reliable button response and clear display feedback. What it does:

• Provides touchpad/buttons and display for selecting oven/range functions and settings
• Sends user commands to the range control so cooking cycles start and stop as selected
• Failure symptoms include unresponsive buttons, blank or garbled display, or range not accepting settings
• May clear intermittent control errors and restore normal control operation when defective

• Disconnect power to the appliance before removing or installing the panel to avoid shock risk
• Handle the display/touchpad carefully to avoid scratching or bending fragile components
• Verify connectors are fully seated and routed away from heat sources before restoring power

This front cover is the exterior cabinet panel that protects internal components and gives the appliance a finished appearance. It restores a clean, secure front and helps shield controls and openings from dust and debris. What it does:

• Replaces a worn, cracked, or damaged front cabinet panel to restore proper fit and appearance
• Protects internal parts and wiring from dust, moisture, and physical damage
• Helps maintain proper airflow and alignment of door or control openings
• Can reduce rattles or gaps caused by a damaged front panel

• One front cover as shown

• Inspect surrounding trim, fasteners, and mounting clips; replace any broken hardware for a secure fit
• Disconnect power to the appliance before beginning work and follow basic electrical safety
• Some models require partial disassembly of the console or outer cabinet; handle painted surfaces carefully to avoid scratches
• Verify correct orientation and alignment before tightening all fasteners

This control panel is the console assembly that lets you select oven and cooktop functions and view settings. It replaces a cracked, faded, or unresponsive console to restore control and visible readouts. What it does:

• Houses the touchpad/buttons and display used to set oven temperature, timers, and bake/broil modes
• Sends user commands to the oven control for cooking functions
• Commonly replaced for unresponsive keys, unreadable or damaged face, or intermittent control behavior
• Works with the oven's electronic control to show status and error codes

• One control panel (console assembly)

• Disconnect power at the breaker before removing the console to avoid shock
• Handle the panel and display carefully to avoid scratching or cracking the fascia
• Some disassembly of the oven console and removal of mounting screws and wire harness connectors is usually required