Maytag Washer Hose Or Tube

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

These replacement 6" FXF vacuum bags capture dust and debris to restore pickup performance and keep the appliance's airflow and motor compartment cleaner. Designed as a direct-fit consumable for compatible bagged upright and canister vacuums. What it does:

• Collects dirt, dust and debris so particles stay contained for easier disposal
• Helps maintain suction by keeping the vacuum's intake and motor chamber clearer
• Reduces dust and allergen re-distribution compared with a torn or overloaded bag
• Replaces worn or full bags that cause reduced capacity, visible dust escaping, or increased odor

• Always unplug the vacuum before removing or installing bags
• Remove the full bag carefully to avoid spilling debris; seal and dispose per local regulations
• Verify correct orientation and secure fit before operating to avoid leaks
• Replace bags regularly; inspect the inlet collar and seals for wear when servicing

This replacement trap sits in the dishwasher's sump/filtration area and captures larger food particles before they reach the pump. It helps maintain cleaning performance and reduce clogs that can lead to poor wash results or draining issues.

• Screens debris to protect the wash and drain pump
• Helps maintain proper water circulation and draining
• Damage or warping can let debris bypass the filter system
• Symptoms include poor cleaning, standing water, unusual grinding noises, or odors

• Disconnect power and shut off water supply before servicing
• Remove the lower rack; take out the lower spray arm and filters to access the trap
• Release the trap's locking tabs/fasteners, remove, and seat the new trap fully
• Reinstall filters and spray arm; run a short cycle to check for leaks and proper operation

The Drain Hose is an OEM part for Whirlpool washing machines. It is a flexible tube that diverts water from the washer tub during drain cycles, guiding it out of the appliance and into a nearby drain source such as a sink. 

Causes of a bad drain hose can include cracks or abrasions developing over time due to repeated bending and flexing during drain cycles. Mineral or hard water buildup inside the hose can also lead to clogs. Other potential causes are physical damage from rodents, pets, or accidental punctures.

Symptoms of a bad drain hose include:

• Incomplete draining or water remaining in the washer tub after cycles  
• Leaks or drips forming around the drain hose connection point
• Puddles or water pooling under or around the washing machine
• Slow drainage during spin cycles

This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washer models.

This replacement hose routes water where the appliance needs it, helping restore proper filling and draining to prevent leaks or poor performance. Designed to match the original fitting and flow path for a reliable repair. What it does:

• Directs water between components to enable normal fill and drain cycles
• Prevents leaks when properly connected and clamped
• Restores proper drainage and prevents standing water or slow emptying
• Helps stop symptoms like intermittent filling, error codes related to water flow, or visible leaking

• Disconnect power and shut off the water supply before servicing
• Inspect and replace any worn clamps or fittings for a secure seal
• Route hose as original to avoid kinks and ensure proper flow

This water inlet hose directs incoming water into the appliance for normal operation, providing a reliable pathway that maintains safe, consistent water flow. Use this OEM-fit hose to replace a cracked, leaking, or damaged inlet line. What it does

• Carries incoming water from the home's supply to the appliance's water valve or fill assembly.
• Restores proper filling when an old hose leaks, is split, or becomes deteriorated.
• Helps prevent water damage and maintains normal cycle performance when functioning correctly.
• Compatible with repairs where the original inlet hose is worn, kinked, or blocked.

• One new replacement water inlet hose.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect hose fittings and seals; replace any worn clamps or gaskets for a secure, watertight connection.
• Route the hose without sharp bends or kinks and secure per the appliance's routing clips.

This replacement drain hose routes wastewater away from the appliance to the household drain so your unit can empty reliably and avoid standing water. Designed to match the original fit and flow path for easy replacement. What it does:

• Carries waste water from the appliance to the home drain or pump outlet
• Helps prevent water backup, pooling, or slow draining when functioning correctly
• Replaces cracked, split, or deteriorated hose that can cause leaks
• Restores the intended water flow path to reduce the risk of overflow or damage

• Disconnect power and shut off water supply before beginning any repair
• Remove and replace the old hose, using existing clamps or new clamps rated for appliance use
• Route the hose to match the original path; avoid kinks or tight bends that restrict flow
• After installation, restore power/water and run a short cycle to check for leaks