Maytag Washer Parts

Bought a new one one and slid it in myself. Read more

Replaced It With New One Read more

• Will not drain
• Burning smell
• Noisy

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

Replaced both hot and cold water inlet valves. Works like a charm, issue resolved. Read more

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more

In the past we’ve fixed the latch with just high speed great. This time we ordered a new latch and replaced it. Washing machine has been working perfectly ever since. It was very easy to find the right part by simply entering the model number of my washing machine. It was quick delivery and the correct part. Very happy to have a working washing machine again. Read more

I replaced the hose between the tub and the pump. The clamp screws were quite rusted but I used a socket wrench on them since they have hex heads in addition to the screwdriver slot. If I had tried to use a screwdriver, I think it would have been difficult. I did not reuse the original clamps but replaced them with hardware store hose clamps. Read more

I noticed a lot of water on the floor one day. I had no idea where it came from (all pipes in the area near the stationary tub were dry, there was a small wet spot near the washer, but most of the water was more than 2ft from it). Started a small load and noticed water running down the outside of the unit. Immediately stopped the cycle and removed the front of the washer. Restarted the cycle and could see water spraying from the intake hose. Stopped the cycle and advanced it to spin to... Read more

Replaced water inlet unit. Read more

• Lid or door will not open
• Lid or door won't close

The greatest thing about Appliance Parts Pros is that when I ordered the part, I watched the 2 minute video on how replace it. When the part arrived, the next day by the way, I simply did as the video did. I love this site! I've repaired my washer and dryer and saved so much money simply by watching these videos and ordering the part. Customer service is amazing as well. They have always given me the correct information and I've never had to wait longer than a couple of minutes for... Read more

I had previously replaced the transmission in my two year old Whirlpool Cabrio washing machine. Overall it was in good shape but gets heavy use. That repair was approximately $200 and worked for several months. Recently it began leaking. At first I thought it was the tub-to-shaft seal. I replaced this part but it was still leaking. It turns out it was the simplest of things... The drain hose was not connected very well! I replaced the drain hose ($11 part) and while I was at it I... Read more

Replaced agitator and washplate bolt and washer. Normally this would have been a 5 min job, however the bolt wouldn't come loose. The teeth on the agitator were worn down and the shaft the bolt screws into would turn with the bolt when trying to loosen it. I had to cut out the agitator using a dremel and hold the shaft in place with a vise grip in order to unscrew the bolt. Once the bolt was out I used WD-40 to help get the agitator off the gears. Job took much longer than normal, but I... Read more

First, DO NOT call Sears for parts, their call center knows nothing about the product. App-Pros are the best for help and the right parts. I figured to repair, replace all seals and any item that shows need to and all items that have to do with the spin that may be bad. Repair videos great help. I will start from the "bottom" up, the repairs were not done in this order, just a list of what I did and notes. Replaced-- motor drive coupling, (checked out transmission ok), thrust washer,... Read more

• Will not fill with water

Our original discussion with a parts rep. led us to change the control panel as we had tested the valves for continuity and had it. Changing the panel did not fix the problem. As we had power continuity, we then removed the hoses from the cold water valve and checked the flow. The wash fill side of the valve had only a trickle of water, so we ordered a new cold inlet valve and replaced it. Problem solved, washer working like it's new. Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Ordered a new inlet water valve . Super fast delivery ordered on a Wednesday afternoon was here Thursday morning , standard shipping , I was impressed !! Removed the old valve , installed the new , checked for leaks no issues , washer is back on line and my Honey is very happy with me . Read more

• Marks left on clothes

Searching for paddles or baffles led me to Appliance Parts. Discovered I didn't have to buy anything in order to view the video which is a pretty nice feature to see if my skills are up to it. "How in the world do I repair something without external screws?" "Take the top off the machine to see if there are any mounting screws and then just smack the baffles toward the rear of the machine with a mallet to loosen and remove?" Easy, really easy. My wife was missing an underwire to one of her bras... Read more