Maytag Washer Parts

Replacement lid hinge for top-load washers. Mounts between the lid and cabinet. Replace when bent, twisted, rusted through, or cracked from wear.

If your washer dispenser drawer won't open or the handle broke off, this dispenser drawer handle restores access to detergent compartments. Easy DIY fix.

Secures washer tub during transport to prevent internal damage. Install in back panel before moving. Replace if missing, rusted, or corroded. Set of 4 required.

Fix washer won't drain issues with this lower wiring harness. Restores electrical connections between drain pump and control components.

Fix a washer agitator that won't turn or spins weakly with this lower agitator base. Restores proper wash action when worn, cracked, or stripped.

Felt seal that fits around your dishwasher's door vent to contain steam and moisture. Replace if you notice condensation or minor leaks during cycles.

This is the control knob assembly for the appliance's control shaft. It lets you select settings by turning the shaft without tools. A worn or cracked knob can slip, spin freely, or make it hard to set temperatures or cycles.

• Rotates the control shaft to adjust settings
• Replaces knobs that are cracked, stripped, or hard to turn
• Helps restore precise selection of temperatures and cycles
• Common symptoms include a loose knob, no response when turning, or difficulty gripping

• Disconnect power and allow hot surfaces to cool before service
• Pull the old knob straight off the shaft; avoid prying against the panel
• Align the new knob with the shaft flat and press firmly until seated
• Test operation through the full range of settings

Secures washer base frame during transport and installation. Replace if bolt is lost, stripped, or damaged during delivery or moving to prevent rocking.

Replace a cracked or broken dispenser cover that exposes internal parts. This outer trim panel protects wiring and restores appearance. Easy hand removal.

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.

• Supports and self-levels the rear of the cabinet to maintain stability on uneven floors
• Helps address wobbling/rocking, excessive vibration, rattling or "walking," and an appliance that won't sit level
• Replaces a rear leg that is missing, cracked, or worn
• Promotes smoother operation by helping the unit sit properly level

• Disconnect power; if applicable, turn off the water supply
• With assistance, carefully tilt the appliance to access the rear base
• Remove the damaged rear leg from its mount and install the new leg, ensuring it seats fully
• Lower the unit, verify level with a bubble level, and adjust front legs as needed for final leveling

Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.

Internal drum lifter that tumbles clothes during wash cycles. Replace if cracked, broken, loose, or missing to restore proper tumbling and prevent snags.

Washer won't start or lid won't latch? This lid strike assembly provides the catch point for secure lid closure. Easy DIY fix in under 30 minutes.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Suspension rod ball and bushing kit with 4 balls and 4 bushings. Replaces worn or broken suspension components that cause washer movement and noise.